
L i f e B o o k B 6 2 0 0 S e r i e s – S e c t i o n F i v e
Problem | Possible Cause | Possible Solutions |
|
|
|
|
|
|
The system powers up, and | The boot sequence settings of | Set the operating source by pressing the [F2] key |
displays power on informa- | the setup utility are not | while the Fujitsu logo is on screen and enter the |
tion, but fails to load the | compatible with your | setup utility and adjust the source settings from the |
operating system. | configuration. | Boot menu. See “BIOS Setup Utility” on page 31. |
|
|
|
| You have a secured system | Make sure you have the right password. Enter the |
| requiring a password to load | setup utility and verify the Security settings and |
| your operating system. | modify them as accordingly. See “BIOS Setup |
|
| Utility” on page 31. |
|
|
|
An error message is | Power On Self Test (POST) has | See the Power On Self Test (POST) messages to |
displayed on the screen | detected a problem. | determine the meaning of the problem. Not all |
during the LifeBook note- |
| messages are errors; some are simply status indica- |
book boot sequence. |
| tors. See “Power On Self Test Messages” on page 62. |
|
|
|
Your system display won’t | The system may be password- | Check the status indicator panel to verify that the |
turn on when the system is | protected. | Security icon is blinking. If it is blinking, enter your |
turned on or when the |
| password. |
system has resumed. |
|
|
|
|
|
Your notebook appears to | BIOS setup changes were not | Make sure you select Save Changes And Exit when |
change setup parameters | saved when you exited the | exiting the BIOS setup utility. |
when you start it. | BIOS setup utility, returning it |
|
| to previous settings. |
|
|
|
|
| The BIOS CMOS | Contact your support representative for repairs. |
| battery has failed. | This is not a user serviceable part but has a normal |
|
| life of 3 to 5 years. |
|
|
|
Video Problems |
|
|
|
|
|
The | The optional Port Replicator is | Pressing [F10] while holding down the [Fn] key |
when you turn on your | attached, an external monitor | allows you to change your selection of where to send |
notebook. | is plugged in, and the note- | your display video. Each time you press the key |
| book is set for an external | combination you will step to the next choice. The |
| monitor only. | choices, in order are: |
|
| monitor only, both |
|
| monitor. |
|
|
|
| The angle of the display and | Move the display and the brightness control until |
| the brightness settings are not | you have adequate visibility. |
| adequate for your lighting |
|
| conditions. |
|
|
|
|
| The power management | Press any button the keyboard, or move the mouse |
| timeouts may be set for very | to restore operation. If that fails, push the Suspend/ |
| short intervals and you failed | Resume button. (The display may be shut off by |
| to notice the display come on | Standby mode, Auto Suspend or Video Timeout) |
| and go off again. |
|
|
|
|
The notebook turned on | Power On Self Test (POST) has | Contact your support representative. |
with a series of beeps and | detected a failure that does not |
|
your display is blank. | allow the display to operate. |
|
|
|
|
Your system display won’t | The system may be password- | Check the status indicator panel to verify that the |
turn on when the system is | protected. | Security icon is blinking. If it is blinking, enter your |
turned on or when the |
| password. |
system has resumed. |
|
|
|
|
|
60