Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MHT2080BH, MHT2060BH, MHT2040BH manual Read LOG EXT X2F

Models: MHT2080BH MHT2060BH MHT2040BH

1 264

Download 264 pages 35.52 Kb

Page 197

5.3 Host Commands

(43) READ LOG EXT (X'2F')

The READ LOG EXTEND command reads versatile log data. Versatile log data includes the Extended SMART Comprehensive Error log, the Extended SMART Self-test log, and the SMART Selective log. The effectiveness of the log types depends on customization. All types of versatile log data except Read Log Ext log page 10h are customizable. For the protocol concerning data transfers, see Section 5.4.

The number of the log to be read is specified as the Log address. For log data consisting of multiple sectors, a sector offset can be specified as an instruction so that data transfer starts from the specified sector. The number of sectors to be transferred is specified as the Sector count.

If an error occurs in the FP Queued protocol, Read Log Ext log page 10h containing the error information is transferred. This Read Log Ext log page can be read by specifying Sector offset = 00h, Sector count = 01h, and Log address = 10h. For the data format of Read Log Ext log page 10h, see Table 5.29.

If this command is not supported, or if an invalid value is specified for the Log address, Sector count, or Sector offset, the Aborted Command error occurs.

•Error reporting conditions

(1)An error was detected during power-on processing (ST = 51h, ER = 04h).

(2)An error was detected during wake-up processing (in cases where wake-up processing is required before execution of this command)

(ST = 51h, ER = 04h).

(3)An error that cannot be corrected with ECC occurred (ST = 51h, ER = 40h).

(4)The sync byte indicating the beginning of a sector was not found (ST = 51h, ER = 01h).

(5)An invalid log sector address or invalid Sector count (number of sectors to be transferred) is specified (ST = 51h, ER = 04h).

(6)A SATA communication error occurred (ST = 51h, ER = 0Ch).

C141-E203-01EN

5-123

Image 197

Fujitsu MHT2080BH, MHT2060BH, MHT2040BH manual Read LOG EXT X2F

Contents

Disk Drives Product Manual MHT2080BH, MHT2060BH, MHT2040BHHandling of This Manual For Safe OperationRevision History This page is intentionally left blank Overview of Manual PrefaceConventions Conventions for Alert MessagesOperating Environment Liability Exception This page is intentionally left blank Important Alert Messages Important Alert ItemsThis page is intentionally left blank MHT2040BH Disk Drives Product Manual MHT2040BH Disk Drives Maintenance ManualManual Organization This page is intentionally left blank Contents Theory of Device Operation Installation ConditionsInterface 102 Operations IN-1 GL-1Acronyms and Abbreviations AB-1 Figures IllustrationsResponse to power-on when the host is powered Tables Recommended connector specifications for the host systemRelationship between combination of Identifier and Security Device Overview Adaptability FeaturesFunctions and performance Interface Specifications summary Device SpecificationsSpecifications 1/2 MHT2080BH MHT2060BH MHT2040BHModel and product number Specifications 2/2MHT2080BH Examples of model names and product numbersRipple Power RequirementsInput Voltage Current and power dissipation Current Requirements and Power DissipationCurrent fluctuation Typ. at +5 V when power is turned on Environmental SpecificationsPower on/off sequence Environmental specificationsShock and vibration specification Acoustic noise specificationAcoustic Noise Shock and VibrationData assurance in the event of power failure Service lifeReliability Mean time between failures MtbfUnrecoverable read error Error RatePositioning error Media DefectsAdvanced Power Management Advanced power management Device-initiated Interface Power Management Dipm Interface Power Management IPMHost-initiated Interface Power Management Hipm Interface power management This page is intentionally left blank Device Configuration Device Configuration Sata interface System ConfigurationDrive connection Read/write circuitThis page is intentionally left blank Installation Conditions Dimensions DimensionsOrientation MountingIntegration Guidance C141-E144 PCA FrameLimitation of mounting Location of breather Ambient temperature Handling cautions Service areaHios ESDSumitomo 3M Connections with Host System Device connectorRecommended connector specifications for the host system Connector specifications for host systemSignal segment and power supply segment Sata interface cable connection This page is intentionally left blank Theory of Device Operation Subassemblies OutlineDisk SpindleAir filter Circuit ConfigurationServo circuit Spindle motor driver circuitPower Supply Configuration PCA Power-on operation sequence Power-on SequenceSelf-calibration Self-calibration contentsExecution timing of self-calibration Command processing during self-calibrationRead/write preamplifier PreAMP Read/write CircuitWrite circuit RLL code MeeprmlProgrammable filter circuit Read circuitAGC circuit FIR circuit Digital PLL circuitD converter circuit Viterbi detection circuitMicroprocessor unit MPU Servo ControlServo control circuit Servo burst capture circuit Power amplifierA converter DAC Spindle motor control circuitInner guard band IGB Data-surface servo formatData area Outer guard band OGBPhysical sector servo configuration on disk surface Servo frame format Operation to move the head to the reference cylinder Actuator motor controlSeek operation Track-following operationSpindle motor control Start modeAcceleration mode Stable rotation mode This page is intentionally left blank Interface Physical Interface Interface signals5VDC/GND Comreset / CominitComwake Out of band signaling Signal interface regulationPrimitives descriptions Physical Layer Electrical Requirements 1/2 Electrical specificationsOminit COMRESET/CPhysical Layer Electrical Requirements 2/2 Connector pinouts Connector pinoutsLogical Interface Conceptual diagram of communication layersPhysical layer Communication layersLink layer Transport layerShadow Block Register Outline of the Shadow Block RegisterFIS types Outline of the frame information structure FISRegister Host to Device Register Host to Device FIS layoutDMA Active Device to Host Register Device to HostTAG DMA Setup Device to Host or Host to Device BidirectionalBist combinations Bist Active BidirectionalData FIS Bidirectional layout Data Host to Device or Device to Host BidirectionalUNC Error FieldShadow block registers Sector Count Field exp Features Field expSector Number Field exp Cylinder Low Field expDevice/Head Field Cylinder High Field expHS3 HS2 HS1 HS0 HS3Bit Error ERR bit Bit Device Write Fault DF bitStatus field Bit 7 Busy BSY bitBit 2 Software Reset Srst Command FieldDevice Control Field EStatus FieldCommand code and parameters 1/3 Host CommandsCommand code and parameters Command code and parameters 2/3 Command code and parameters 3/3 Command descriptions Recalibrate X’10’ to X’1F’ Error reporting conditionsRead Sectors X’20’ or X’21’ LBA LBA LSBRead Long X’22’ or X’23’ Write Sectors X’30’ or X’31’ 00 *1 Error information Write Long X’32’ or X’33’ Cylinder No. LSB Write Verify X’3C’ Host Commands Read Verify Sectors X’40’ or X’41’ Host Commands Seek X’70’ to X’7F’ Diagnostic code Execute Device Diagnostic X’90’Initialize Device Parameters X’91’ Operation of Download Microcode Download Microcode X’92’Error reporting conditions Standby Immediate X’94’ or X’E0’ Idle Immediate X’95’ or X’E1’ Standby X’96’ or X’E2’ Idle X’97’ or X’E3’ Host Commands ’FF’ Check Power Mode X’98’ or X’E5’Sleep X’99’ or X’E6’ ComresetSmart X’B0’ Features Field values subcommands and functions 1/3 Smart Enable Operations Features Field values subcommands and functions 2/3Smart Disable Operations Smart Read LOGSmart Return Status Features Field values subcommands and functions 3/3’DB’ Smart ENABLE/DISABLE Auto OFF-LINE Key C2h 1FF 11 Format of guarantee failure threshold value data10 Format of device attribute value data Attribute ID Data format version numberCurrent attribute value Status FlagAttribute value for the worst case so far Raw attribute value13 Self-test execution status 12 Off-line data collection statusSelf-test execution status 15 Failure prediction capability flag 16 Drive error logging capability14 Off-line data collection capability Smart error logging Guarantee failure thresholdChecksum 17 Log Directory Data Format18 Data format of Smart Summary Error Log 1/2 Command data structure 18 Data format of Smart Summary Error Log 2/2Error data structure Total number of drive errorsSmart Self-Test 19 Data format of Smart Comprehensive Error Log1FC 20 Smart self-test log data formatSelf-test number Self-test indexCurrent LBA under test 21 Selective self-test log data structureTest Span 22 Selective self-test feature flags Feature FlagsCurrent Span under test Selective Self-test pending time minDevice Configuration Restore Device Configuration XB1Device Configuration Freeze Device Configuration IdentifyDevice Configuration Freeze Lock Features Field = C1h Device Configuration Restore Features Field = C0hDevice Configuration SET Features Field = C3h Device Configuration Identify Features Field = C2hWord Value Content 23 Device Configuration Identify data structureRead Multiple X’C4’ Execution example of Read Multiple command LBA LSB Write Multiple X’C5’ At command issuance Shadow Block Registers setting contents SET Multiple Mode X’C6’ Host Commands Read DMA X’C8’ or X’C9’ LBA Write DMA X’CA’ or X’CB’ Host Commands Read Buffer X’E4’ Flush Cache X’E7’ Write Buffer X’E8’ Identify Device X’EC’ Identify Device DMA X’EE’ ’3FFF’ 24 Information to be read by Identify Device command 1/324 Information to be read by Identify Device command 2/3 24 Information to be read by Identify Device command 3/3 Interface Bit 0 Reserved C141-E203-01EN FIS Host Commands Word Bit Bit 0 1 = Supports the Mode C141-E203-01EN Interface 25 Features field values and settable modes 1/2 SET Features X’EF’25 Features field values and settable modes 2/2 Data Transfer Mode Advanced Power Management APM Automatic Acoustic Management AAM Serial ATA Functions26 Contents of Security SET Password data Error reporting conditions Security UNLOCKX’F2’ When the master password is selectedWhen the user password is selected Host Commands Security Erase Prepare X’F3’ Security Erase Unit X’F4’ Security Freeze Lock X’F5’ Error reporting conditions 28 Contents of security password Error reporting conditions Lbalsb Read Native MAX Address X’F8’SET MAX Address SET MAX X’F9’SET MAX SET Password Features Field = 01h Password information SET MAX Lock Features Field = 02h SET MAX Unlock Features Field = 03h SET MAX Freeze Lock Features Field = 04h SN EXP Read Sector S EXT X’24’ DescriptionCL EXP Read DMA EXT X’25’ Description Read Native MAX Address EXT X’27’ Read Multiple EXT X’29’ Read LOG EXT X2F CL EXP SN EXP 30 Tag field information 29 Data format of Read Log Ext log page 10hWrite Sector S EXT X’34’ Description Write DMA EXT X’35’ Description SET MAX Address EXT X’37’ SET MAX LBA Write Multiple EXT X’39’ Write LOG EXT X3F Error information 132 C141-E203-01EN Read Verify Sector S EXT X’42’ Flush Cache EXT X’EA’ Write Multiple FUA EXT XCE Write DMA FUA EXT X3D Read FP DMA Queued Write FP DMA Queued 31 Command code and parameters 1/2 Error postingCommand Name Sfrw Sfrr31 Command code and parameters 2/2 Execute Device Diagnostic Initialize Device Parameters Command ProtocolNon-data command protocol Host PIO data-in command protocol Piosu Data PIO data-out command protocolPiosu 12 PIO data-out command protocolRead DMA EXT Identfy DMA DMA data-in command protocolWrite DMA EXT FUA EXT DMA data-out command protocolRead FP DMA Queued Write FP DMA Queued Native Command Queuing protocol15 Read FP DMA Queued command protocol 16 Write FP DMA Queued command protocol 17 Power-on sequence Power-on and Comreset18 Comreset sequence Operations Response to power-on Reset and DiagnosisReset and Diagnosis Response to Comreset Response to ComresetResponse to a software reset Response to a software resetPower save mode Power SaveActive mode Active idle modeSleep mode Standby modePower commands Partial mode Interface Power SavePower save mode of the interface Slumber mode 8MB buffer Read-ahead CacheData buffer structure Data that is a target of caching Commands that are targets of cachingCaching operation Invalidating caching-target data Miss-hit Using the read segment bufferFull hit Sequential hitHAP end location of the previous read command Partial hit Write Cache Command that are targets of cachingCache operation Invalidation of cached dataComreset and software reset response Status report in the event of an errorCashing function when power supply is turned on Enabling and disablingThis page is intentionally left blank Glossary Rotational delay Power save modePIO Programmed input-output PositioningAcronyms and Abbreviations This page is intentionally left blank Index Block diagramIndex Device-initiated interface power Frame information structure FIS Moving head to reference cylinder .4-13 RLL algorithm run length limited Read Native MAX AddressSensing and compensating for IN-8 C141-E203-01EN Japan Comment FormDisk Drives Product Manual This page is intentionally left blank C141-E203-01EN This page is intentionally left blank