Fujitsu PCI GigabitEthernet 3.0 4.3 Notes

Chapter 4 LinkAggregation Feature

4.3 Notes

This section explains notes for using the LinkAggregation function. ● LACP (dynamic LinkAggregation function) is not supported.

● Only TCP/IP connection is supported.

● Do not run FJVTS when LinkAggregation is being used.

● If VLAN interface with LinkAggregation function enabled is used, the following must be satisfied.

The number of VLAN interfaces * the number of physical interfaces in group * the number of groups <= 1024

If the above is not satisfied, the system may not work correctly (due to lack of memory resource).

● Only superuser can execute the fjla command.

● The link speed must be the same among the member interfaces in a LinkAggregation group, and duplex mode must be set to full.

● It is necessary to inactivate the corresponding LinkAggregation group with the fjla term command before DR (Dynamic Reconfiguration) or PCI Hot Plug is performed.

● It is necessary to activate corresponding LinkAggregation group with the fjla init command after DR or PCI Hot Plug is completed.

● In a cluster system, takeover of LinkAggregation interfaces is not supported. ● The VLAN interface cannot be specified directly. It is necessary to use the VLAN

interface with LinkAggregation that making the VLAN interface only for the aggregator-interface by a usual VLAN interface making procedure(ifconfig(1M) or making /etc/hostname.fjgi** file).

56

Contents

Page For Safe Operation Revision History Preface Page Contents Contents Chapter 1 Product Outline 1.1 Key Features Table 1.1 GigabitEthernet function 1.2 GigabitEthernet card Specifications 1.2.1 Specifications Table 1.2.1 PCI GigabitEthernet Card Specification Table 1.2.2 PCI Express GigabitEthernet Card Specification 1.2.2 Part Names and Features of Hardware Page Page Page Page Chapter 2 Installing FUJITSU PCI GigabitEthernet Card 2.1 Installation of the GigabitEthernet Card 2.2 Identifying the GigabitEthernet Card 2.3 Cable Connection Figure 2.3.1 PW008GE4 (with Optical Fiber Cable) Figure 2.3.2 PW008GE5 (with Twisted Pair Cat5E Cable) Figure 2.3.3 PW0G8GE1 (with Optical Fiber Cable) Figure 2.3.4 PW0G8GE2 (with Twisted Pair Cat5E Cable) Figure 2.3.5 SE0X7GD2X (with Optical Fiber Cable) Figure 2.3.6 SE0X7GD1X (with Twisted Pair Cat5E Cable) Figure 2.3.7 PW008QG1 (with Twisted Pair Cat5E Cable) Figure 2.3.8 SE0X7GQ1X (with Twisted Pair Cat5E Cable) Page Chapter 3 Setting Configuration Information 3.1 Driver Software Installation 3.2 Environment Setting 3.2.1Configuring the Hostname File 3.2.2Hostname Definition Page 3.2.3 Netmask Value Definition 3.3 Operation Mode Setup 3.3.1 The fjgi.conf File [Parameter Setting] device node of device tree driver name PRIMEPOWER250/450 PW008GE5 PW008GE4 Page 3.3.2 JumboFrame Setup [Method 3: How to specify by fjgi.conf] 3.3.3The ndd Utility parameter status meaning Page Page 3.3.4FCode Settings Page [Returning to Default FCode Settings] 3.4 Discernment Of the GigabitEthernet Interface or GP7000 family 3.4.2 Discernment Of the GigabitEthernet Interface on SPARC Enterprise 3.4Discernment Of the GigabitEthernet Interface 3.5 Network Installation 3.5 Network Installation Page 3.6 VLAN Interface Setup 3.6.1 IEEE 802.1Q TagVLAN Description 3.6.2 Setting Up the VLAN Interface fjgi231003 VLAN interface number = VLAN ID * 1000 + physical instance number Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature Table 4.1.1 Requirements Table 4.1.2 Data Distribution Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1Setting Up the /etc/opt/FJSVla/config File 4.2 Configuration of the LinkAggregation Feature 4.2.2 Using the /etc/opt/FJSVla/bin/fjla Command 4.2.2.2 Inactivate a LinkAggregation Group (fjla term) - Description 4.2.2.3 Display Status and Statistics (fjla stat) - Display Format 4.3 Notes Chapter 5 Troubleshooting Page Appendix A Messages A.1 Console Messages Table A.1.1 Console Messages of the FUJITSU PCI GigabitEthernet driver Appendix A Messages Master Slave Page Table A.1.2 Machine Administration Reported Messages A.2 Command Messages Table A.2 Command Message Page Appendix B On-BoardDiagnostics ACT LED - Location of the LEDs(PW0G8GE1/SE0X7GD2X) - Meaning of the LEDs(PW0G8GE1/SE0X7GD2X) LINK LED - Location of the LEDs(PW0G8GE2) Figure B.5 10/100/1000Base-T(PW0G8GE2) - Meaning of the LEDs(PW0G8GE2) Appendix B On-BoardDiagnostics - Location of the LEDs(SE0X7GD1X) Figure B.6 10/100/1000Base-T* 2ports (SE0X7GD1X) - Meaning of the LEDs(SE0X7GD1X) - Location of the LEDs(PW008QG1/SE0X7GQ1X) Figure B.7 1000Base-T* 4ports (PW008QG1) Figure B.8 1000Base-T* 4ports (SE0X7GQ1X) Page Appendix C Using GigabitEthernet in a Cluster Environment Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D PCI Slot Number and Device Name Table D.1 Slot Number and Device Name Matrix Page Page Page Page Page Page Board Number; Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Appendix E Available Switches Table E.1 With FUJITSU PCI GigabitEthernet 3.0 (PW008GE4/PW0G8GE1/SE0X7GD2X) Table E.2 With FUJITSU PCI GigabitEthernet (PW008GE5/PW0G8GE2/SE0X7GD1X/PW008QG1/SE0X7GQ1X and PRIMEPOWER250/450 secondary LAN port) Table E.4 IEEE802.3 LinkAggregation capable switches