|
|
| A.1 Console Messages | |
|
|
|
| |
No | Message | Cause | Workaround | |
|
|
|
| |
13 | Unable to map adapter registers. | Mapping of the adapter |
| |
registers failed. |
| |||
|
|
| ||
|
|
|
| |
14 | The driver could not allocate | Installed physical | ||
|
| interrupt resources. |
| |
15 | Unable to install interrupt routine. | memory may be | ||
|
|
| insufficient. If this is | |
16 | ddi_create_minor_node failed | Creation of a device file | ||
failed. | not the cause, report | |||
|
| |||
|
|
| this error to your | |
17 | ATTACH failed | The driver was not loaded to | ||
the kernel successfully. | service provider. | |||
|
| |||
|
|
|
| |
18 | OPEN failed: ENOMEM | The driver could not allocate |
| |
|
| resources. |
| |
19 | CLOSE: stream==NULL |
| ||
|
|
|
| |
|
|
| ||
|
| A different protocol is being | interface. If this | |
20 | bind to 802.2 failed | message is still | ||
used. | ||||
|
| displayed, report to | ||
|
|
| ||
|
|
| your service provider. | |
|
|
|
| |
|
|
| With | |
|
| With | PW008GE4/PW0G8GE1/SE0X7 | |
21 | Duplex are invalid !! Please change | PW008GE4/PW0G8GE1/SE0X7GD2X | GD2X, only full duplex is | |
the partner's duplex Full. | , the other end is using half | available. Change the | ||
| ||||
|
| duplex mode. | duplex mode of the other | |
|
|
| end to Full. | |
|
|
|
| |
22 | DL_DETACH_REQ: No board ptr | The adapter was not | Check the mounting | |
recognized. | status of the adapter. | |||
|
| |||
|
|
|
| |
|
| The driver could not allocate |
| |
23 | fjgi_param_register error | resources for the ndd |
| |
|
| parameter. |
| |
|
|
|
| |
24 | fjgi_board_alloc_mem failed !! | The driver could not allocate |
| |
resources. |
| |||
|
|
| ||
|
|
|
| |
25 | Error filling TX ring | The driver could not allocate | Installed physical | |
transmit resources. | ||||
|
| memory may be | ||
|
|
| ||
26 | status block can't alloced! | The driver could not allocate | ||
insufficient. If this is | ||||
|
| status information | ||
27 | status block can't alloced handle! | |||
not the cause, report | ||||
|
| resources. | ||
28 | status block can't bind handle! | |||
this error to your | ||||
|
|
| ||
| fjgi_board_init_mem: Failed to | The driver could not allocate | ||
29 | service provider. | |||
dma_alloc !! | DMA resources. | |||
|
| |||
|
|
|
| |
30 | statistic block can't alloced! | The driver could not allocate |
| |
|
| statistic information |
| |
31 | hwmib block can't alloced handle! |
| ||
|
| resources. |
| |
32 | hwmib block can't bind handle! |
| ||
|
|
|
| |
33 | fjgi_board_init_mem: Failed to dma | The driver could not allocate |
| |
alloc2!! | DMA resources. |
| ||
|
| |||
|
|
|
| |
|
| The value of LinkSpeed_A in | Set the correct value for | |
34 | Illegal value for LinkSpeed_A | the configuration file is | ||
LinkSpeed_A. | ||||
|
| incorrect. | ||
|
|
| ||
|
|
|
| |
35 | fjgi_hw_init:Step 22 failed | An error occurred during | A hardware failure | |
|
| initialization of the | occurred. Please contact | |
36 | fjgi_hw_init:Step 23 failed | |||
|
| adapter. | your service provider. | |
37 | fjgi_hw_init:Step 43 failed | |||
|
|
|
| |
38 | Illegal combination of values AutoNeg | Auto speed can not be used in | Set a value other than | |
and Speed | fixed mode. | Auto for LinkSpeed_A. | ||
| ||||
|
|
|
|
61