Manuals / Fujitsu Siemens Computers / Computer Equipment / Printer

Fujitsu Siemens Computers X103 SFF manual Vertical operating position, Preparing for use

Models: X103 SFF

1 49

Download 49 pages 30.42 Kb

Page 15

Image 15

Preparing for use

Vertical operating position

Proceed as follows to operate the device in the vertical operating position:

► If necessary, disconnect the cables.

Use the base feet contained in the accessory pack when it is to be used in a vertical position:

► Place the feet of the device on a non-slip surface.

► Place the device on the base feet (see illustration).

► If necessary, reconnect the cables.

	!	The set-up direction is specified. The ON/OFF switch must be at the top to ensure
	!	sufficient ventilation.
		sufficient ventilation.

The vertical operating position is only permissible with base feet. The base feet provide for sufficient ventilation on the underside of the device.

VFY-SCED103S, edition 1

Page 15

Image 15

Fujitsu Siemens Computers X103 SFF manual Vertical operating position, Preparing for use

Contents

Edition X103 SFF Professional PC Operating Manualyour sales partner your sales outlet Further information can be found in the Safety and Warranty manualsAre there our Hotline/Help DeskPage Order No. VFY-SCED103S This manual was produced byPublished by Fujitsu Siemens Computers GmbH AG 08/05 EditionIntroduction Important notes Preparation for use and operation Troubleshooting and tips System expansions Technical data IndexEdition X103 SFF Operating ManualPentium is a registered trademark of Intel Corporation, USA Copyright Fujitsu Siemens Computers GmbHOffenders will be liable for damages VFY-SCED103S, edition ContentsSettings in BIOS Setup Troubleshooting and tipsInstalling and removing the hard disk ContentsInstalling the drive cage Removing and installing accessible drivesYour Edition X103 SFF Notational conventionsThis font Page Transporting the device Safety notesCleaning the device Important notesCE marking for devices without radio component Energy saving, disposal and recyclingCE marking Important notesExternal devices Steps for initial setupPreparing for use Unpacking and checking the deliverySetting up the device Preparing for use Vertical operating positionHorizontal operating position with rubber feet Connect the monitor, mouse and keyboardConnecting a PS/2 mouse Connecting the monitorConnecting the mouse Connecting a keyboardConnecting the device to the mains voltage Initial switch-on Software will be installed230 = 200 V to Connecting cables Connecting external devicesSwitching on monitor and device Installing the softwarePorts provided by the device Disconnecting cablesDevice drivers Connecting external devices to the parallel or serial portConnecting external devices to the USB ports Port settingsPage Switching the device on Switching off the deviceOperation 3 - Hard disk indicator Indicators provided by the device1 - Drive indicator, e.g. DVD 2 - Floppy disk indicatorEnter key ON/OFF switch optionalKeyboard Important keys and key combinationsAlt Gr e.g. German keyboard Warm bootMenu key Shift keyTo remove a diskette Settings in BIOS SetupWorking with floppy disks To insert a diskettePage Internal power supply overloaded Troubleshooting and tipsInstalling new software The mains voltage supply is faultyMonitor is switched off The device cannot be switched off with the ON/OFF switchTroubleshooting and tips Cause The device has not been switched on with the ON/OFF switchSelect Safe Mode or Safe Mode with Network No mouse pointer displayed on the screenThe floppy disk cannot be read or written Wrong monitor has been set under Window XPTips Error messages on the screenRestoring the hard disk contents Time and/or date is not correctInformation about boards System expansionsClosing the casing Opening and closing the casingSystem expansions Opening the casingRemoving a board Installing a boardAssembling and dismantling low-profile units Removing the holding plateRemoving the front panel Inserting and removing the drive cageRemoving the drive cage Removing the cross-pieceSystem expansions Installing the drive cageDisconnecting cables Removing the drive cage Attaching the drive cageInserting the wires Securing the metal frame Attaching the front panelSystem expansions System expansions Installing and removing drivesInstalling the cross-piece IDE drives and serial ATA drivesRemoving and installing accessible drives Installing and removing the hard diskSystem expansions System expansions Upgrading main memory Replacing lithium batteryExtensions to the mainboard Making changes on mainboardSystem expansions Following changesPage Electrical data Technical dataDimensions WeightPage Index C CableD Data Index flashes Index