Manuals / Fujitsu Siemens Computers / Computer Equipment / Printer

Fujitsu Siemens Computers X103 SFF manual The device cannot be switched off with the ON/OFF switch

Models: X103 SFF

1 49

Download 49 pages 30.42 Kb

Page 30

Troubleshooting and tips

Troubleshooting and tips

The device cannot be switched off with the ON/OFF switch

Cause: The device has not been switched on with the ON/OFF switch.

►Press the ON/OFF switch again.

Cause: System crash

►Press the ON/OFF switch for at least 4 seconds, until the device switches off.

i	The operating system is not shut-down properly in the process. Error messages are
	therefore possible the next time the system is booted.

The screen stays blank

If your screen remains blank this may be due to the following:

Monitor is switched off

►Switch your monitor on.

Power saving has been activated (screen is blank)

►Press any key on the keyboard.

or

►Deactivate the screen saver. If necessary, enter the appropriate password.

Brightness control is set to dark

►Adjust the brightness control. For detailed information, please refer to the operating manual supplied with your monitor.

Power cable not connected

►Switch off the monitor and the device.

►Check that the monitor power cable is properly connected to the monitor and to a grounded mains outlet or to the monitor socket of the device.

►Check that the device power cable is properly plugged into the device and a grounded mains outlet.

►Switch on the monitor and the device.

Monitor cable not connected

►Switch off the monitor and the device.

►Check that the monitor cable is properly connected to the device and monitor.

►Switch on the monitor and the device.

22	VFY-SCED103S, edition 1

Image 30

Fujitsu Siemens Computers X103 SFF manual The device cannot be switched off with the ON/OFF switch, The screen stays blank

Contents

Professional PC Operating Manual Edition X103 SFFour Hotline/Help Desk Further information can be found in the Safety and Warranty manualsAre there your sales partner your sales outletPage Fujitsu Siemens Computers GmbH AG 08/05 Edition This manual was produced byPublished by Order No. VFY-SCED103SOperating Manual Troubleshooting and tips System expansions Technical data IndexEdition X103 SFF Introduction Important notes Preparation for use and operationPentium is a registered trademark of Intel Corporation, USA Copyright Fujitsu Siemens Computers GmbHOffenders will be liable for damages Troubleshooting and tips ContentsSettings in BIOS Setup VFY-SCED103S, editionRemoving and installing accessible drives ContentsInstalling the drive cage Installing and removing the hard diskYour Edition X103 SFF Notational conventionsThis font Page Important notes Safety notesCleaning the device Transporting the deviceImportant notes Energy saving, disposal and recyclingCE marking CE marking for devices without radio componentUnpacking and checking the delivery Steps for initial setupPreparing for use External devicesSetting up the device Vertical operating position Preparing for useConnect the monitor, mouse and keyboard Horizontal operating position with rubber feetConnecting a keyboard Connecting the monitorConnecting the mouse Connecting a PS/2 mouseConnecting the device to the mains voltage Initial switch-on Software will be installed230 = 200 V to Installing the software Connecting external devicesSwitching on monitor and device Connecting cablesDisconnecting cables Ports provided by the devicePort settings Connecting external devices to the parallel or serial portConnecting external devices to the USB ports Device driversPage Switching the device on Switching off the deviceOperation 2 - Floppy disk indicator Indicators provided by the device1 - Drive indicator, e.g. DVD 3 - Hard disk indicatorImportant keys and key combinations ON/OFF switch optionalKeyboard Enter keyShift key Warm bootMenu key Alt Gr e.g. German keyboardTo insert a diskette Settings in BIOS SetupWorking with floppy disks To remove a diskettePage The mains voltage supply is faulty Troubleshooting and tipsInstalling new software Internal power supply overloadedCause The device has not been switched on with the ON/OFF switch The device cannot be switched off with the ON/OFF switchTroubleshooting and tips Monitor is switched offWrong monitor has been set under Window XP No mouse pointer displayed on the screenThe floppy disk cannot be read or written Select Safe Mode or Safe Mode with NetworkTime and/or date is not correct Error messages on the screenRestoring the hard disk contents TipsSystem expansions Information about boardsOpening the casing Opening and closing the casingSystem expansions Closing the casingRemoving the holding plate Installing a boardAssembling and dismantling low-profile units Removing a boardRemoving the cross-piece Inserting and removing the drive cageRemoving the drive cage Removing the front panelAttaching the drive cage Installing the drive cageDisconnecting cables Removing the drive cage System expansionsInserting the wires Securing the metal frame Attaching the front panelSystem expansions IDE drives and serial ATA drives Installing and removing drivesInstalling the cross-piece System expansionsRemoving and installing accessible drives Installing and removing the hard diskSystem expansions System expansions Making changes on mainboard Replacing lithium batteryExtensions to the mainboard Upgrading main memoryFollowing changes System expansionsPage Weight Technical dataDimensions Electrical dataPage Index C CableD Data Index Index flashes