Screw | Gateway 980 specs

Installing drives

2 If a drive has failed, determine which drive has failed by running storage console software. Match the software’s SCSI ID for the failed drive with the SCSI ID number to the left of the hot-swap bays.

3 Pull the drive tray’s lever away from the server, then pull the tray straight out of the server.

Caution

Before you remove a failed drive, use the appropriate software and utilities installed on the server to stop all activity on the failed drive. Instructions for using the software are provided by the software manufacturer. Failure to do so may destroy the data on the drive.

4 If you are replacing a hard drive, remove the four screws that secure the hard drive to the drive tray, then remove the drive from the tray.

Screw

Screw

Screw

Screw

- OR -

www.gateway.com

43

Image 48

Gateway 980 manual Screw

Contents

Page Contents Troubleshooting Iii 107111 119Page Checking Out Your GatewayServer Front Front Back Interior System board Left side Right side System board Getting Help Server Companion CDGateway Web site Setting UpServerYour Setting up the hardware Converting to a rackmount server Protecting from power source problems Surge protectors Uninterruptible power supplies Line conditioners When the power It means Indicator is Starting your serverTo start the server Understanding the power-on self-test To select which device your server boots from Turning off your server To turn off the server Setting up the operating system MaintainingServerYour Cleaning your server Caring for your server Cleaning tips Cleaning the tape drive Preparing for system recovery Recording the Bios configurationTo record your Bios configuration System administration To set the Bios security passwordsGateway Server Manager Server security Resetting Bios passwords on Option Description Using your Server Companion CD ComponentsInstalling Preparing to install components Selecting a place to workGathering the tools you need Preventing static electricity discharge Opening the server case To open the server case Opening the server case Thumbscrews Opening the server case Closing the server case To close the server case Closing the server case Installing drives Installing an IDE drive To install a 5.25-inch drive Installing Components IDE hard drive screws Mounting rail screw Installing drives Screw Follow the instructions in Closing the server case on Installing a Scsi hard drive To install a hard drive Screw Installing Components Installing memory To install or replace memory Installing PCI expansion cards PCI slot Description To replace, add, or reseat a PCI expansion card Release lever Card retention cover Installing Components Follow the instructions in Closing the server case on Installing a processor To replace a processor Installing a processor Remove the heat sink Processor 1 fan connector Processor 2 fan connector Page Replacing the power supply To replace the power supply Replacing the power supply Replacing the Scsi backplane To replace the Scsi backplane Replacing the Scsi backplane Installing Components Thumbscrew Installing Components Follow the instructions in Closing the server case on Replacing the system board To replace the system board Replacing the system board Installing Components Replacing a fan To replace a fan Follow the instructions in Closing the server case on Replacing the Cmos battery To replace the battery Battery Replacing the Cmos battery Installing Components Using the Bios Setup Utility Opening the Bios Setup utility To open the Bios Setup utility Updating the Bios Recovering the BiosTo update the Bios To recover the old Bios Resetting the Bios To reset the Bios Resetting the Bios Using the Bios Setup Utility Troubleshooting Safety guidelines Error messages Invalid password Memory errors were detected while the system started upMemory size error Invalid partition table Troubleshooting Battery replacementFirst steps Beep codes Settings in the Bios Setup utility are not retained Beeps Description Troubleshooting steps CD drive Diskette drive Expansion cards Hard driveYour server does not recognize an expansion card You receive a Non-system disk or disk error error message Your server does not recognize an IDE driveYour server does not recognize a Scsi drive To repair the master boot record InternetTo download the GWScan utility Keyboard MemoryModem telephone dial-up To check the dialing properties in Windows 2000 Server Your 56K modem does not connect at 56K Monitor Modem is not recognized by your serverYour server is running but there is no picture Color is not uniform Power You press the power button, but the server does not turn onWhen you turn on the server, it makes several short beeps Processor Telephone support Before calling Gateway Technical Support Resource Service description How to reach Telephone support Resource Service description For more information Tutoring and training SpecificationsServer a System specifications System board specifications Environmental specifications Variable Requirements Video specifications Resolution supportRefresh Rate Hz Resolution Electronic specifications Memory mapInterrupts Address Range hex Amount Function PCI interrupt routing Device Interrupt a Interrupt B Interrupt C Interrupt D Additional specifications To view all Bios settings 107 Bios menu Bios submenu Setting Value 108 109 110 Important safety information Setting up your system111 Replacement parts and accessories Care during use 113 Regulatory compliance statements United States of America FCC declaration of conformity Product Canada Industry Canada IC Unintentional emitter per ICES-003 Laser safety statement California Proposition 65 Warning All Rights Reserved Trademark Acknowledgments Index 119 120 LAN 121 See card 122 Bios 123 124 125 126