Replacing the Scsi backplane | Gateway 980 manual

Follow the instructions in “Opening the server case” on page 28.

Chapter 4: Installing Components

Replacing the SCSI backplane

Your server has two hot-swap cages that can each hold four SCSI drives. Each hot-swap cage is connected to a SCSI backplane. The pictures in this procedure show replacing the upper SCSI backplane. The other backplane can be replaced in the same manner.

To replace the SCSI backplane:

1 Follow the instructions in “Preventing static electricity discharge” on page 27.

2

3 Remove the fan nearest the SCSI backplane. For instructions, see “Replacing a fan” on page 69.

4 Remove each of the drives from the hot-swap cage, and note the location of each drive. For instructions, see “Installing a SCSI hard drive” on page 42.

5 Loosen the four captive thumbscrews on the front of the hot-swap cage.

Thumb- screws

Thumb- screws

60	www.gateway.com

Image 65

Gateway 980 manual Replacing the Scsi backplane, To replace the Scsi backplane

Contents

Page Contents Troubleshooting 107 Iii111 119Page Checking Out Your GatewayServer Front Front Back Interior Left side System board System board Right side Gateway Web site Getting HelpServer Companion CD Setting UpServerYour Converting to a rackmount server Setting up the hardware Surge protectors Protecting from power source problems Line conditioners Uninterruptible power supplies To start the server When the power It means Indicator isStarting your server To select which device your server boots from Understanding the power-on self-test To turn off the server Turning off your server Setting up the operating system MaintainingServerYour Caring for your server Cleaning your server Cleaning tips Cleaning the tape drive To record your Bios configuration Preparing for system recoveryRecording the Bios configuration To set the Bios security passwords System administrationGateway Server Manager Server security Option Description Resetting Bios passwords on Using your Server Companion CD ComponentsInstalling Gathering the tools you need Preparing to install componentsSelecting a place to work Preventing static electricity discharge To open the server case Opening the server case Opening the server case Thumbscrews Opening the server case To close the server case Closing the server case Closing the server case Installing drives To install a 5.25-inch drive Installing an IDE drive Installing Components IDE hard drive screws Mounting rail screw Installing drives Screw Follow the instructions in Closing the server case on To install a hard drive Installing a Scsi hard drive Screw Installing Components Installing memory To install or replace memory PCI slot Description Installing PCI expansion cards To replace, add, or reseat a PCI expansion card Release lever Card retention cover Installing Components Follow the instructions in Closing the server case on To replace a processor Installing a processor Installing a processor Remove the heat sink Processor 1 fan connector Processor 2 fan connector Page Replacing the power supply To replace the power supply Replacing the power supply To replace the Scsi backplane Replacing the Scsi backplane Replacing the Scsi backplane Installing Components Thumbscrew Installing Components Follow the instructions in Closing the server case on To replace the system board Replacing the system board Replacing the system board Installing Components To replace a fan Replacing a fan Follow the instructions in Closing the server case on To replace the battery Replacing the Cmos battery Battery Replacing the Cmos battery Installing Components Using the Bios Setup Utility To open the Bios Setup utility Opening the Bios Setup utility Recovering the Bios Updating the BiosTo update the Bios To recover the old Bios To reset the Bios Resetting the Bios Resetting the Bios Using the Bios Setup Utility Troubleshooting Safety guidelines Error messages Memory errors were detected while the system started up Invalid passwordMemory size error Invalid partition table First steps TroubleshootingBattery replacement Beep codes Beeps Description Troubleshooting steps Settings in the Bios Setup utility are not retained Diskette drive CD drive Your server does not recognize an expansion card Expansion cardsHard drive Your server does not recognize a Scsi drive You receive a Non-system disk or disk error error messageYour server does not recognize an IDE drive To download the GWScan utility To repair the master boot recordInternet Modem telephone dial-up KeyboardMemory Your 56K modem does not connect at 56K To check the dialing properties in Windows 2000 Server Modem is not recognized by your server MonitorYour server is running but there is no picture Color is not uniform You press the power button, but the server does not turn on PowerWhen you turn on the server, it makes several short beeps Processor Before calling Gateway Technical Support Telephone support Telephone support Resource Service description How to reach Tutoring and training Resource Service description For more information SpecificationsServer a System specifications System board specifications Variable Requirements Environmental specifications Refresh Rate Hz Resolution Video specificationsResolution support Memory map Electronic specificationsInterrupts Address Range hex Amount Function Device Interrupt a Interrupt B Interrupt C Interrupt D PCI interrupt routing Additional specifications 107 To view all Bios settings 108 Bios menu Bios submenu Setting Value 109 110 111 Important safety informationSetting up your system Care during use Replacement parts and accessories 113 United States of America Regulatory compliance statements Product FCC declaration of conformity Industry Canada IC Unintentional emitter per ICES-003 Canada California Proposition 65 Warning Laser safety statement Trademark Acknowledgments All Rights Reserved 119 Index LAN 120 See card 121 122 123 Bios 124 125 126