GE EPM 6000 Multi-function Power Metering System instruction manual PT denominator

CHAPTER 5: COMMUNICATIONS

	HEX		DESCRIPTION1	FORMAT	RANGE6	UNITS OR	COMMENTS	# REG
ADDRESS						RESOLUTION
7532	-	7532	PT denominator	UINT16	1 to 9999	none		1
							MMMMmmmmmmmm is PT multiplier	1
						mmmmmmmm	(1, 10, 100, 1000),
7533	-	7533	PT multiplier & hookup	UINT16	bit-mapped		hhhh is hookup enumeration (0 = 3
						MMMMhhhh
							element wye[9S], 1 = delta 2 CTs[5S], 3
							= 2.5 element wye[6S])
							iiiiii = interval (5,15,30,60)	1
7534	-	7534	Averaging Method	UINT16	bit-mapped	--iiiiii b----sss	b = 0-block or 1-rolling
							sss = # subintervals (1,2,3,4)
							pppp = power scale (0-unit, 3-kilo, 6-	1
							mega, 8-auto)
							nn = number of energy digits (5-8 -->
							0-3)
7535	-	7535	Power & Energy Format	UINT16	bit-mapped	pppp--nn -eee-ddd	eee = energy scale (0-unit, 3-kilo, 6-
							mega)
							ddd = energy digits after decimal
							point (0-6)
							See note 10.
							eeeeeeee = op mode screen rows	1
			Operating Mode Screen
7536	-	7536		UINT16	bit-mapped	00000000 eeeeeeee	on(1) or off(0), rows top to bottom are
			Enables
							bits low order to high order
7537	-	753D	Reserved					7
								1
							g = enable alternate full scale
							bargraph current (1=on, 0=off)
							nn = number of phases for voltage &
							current screens (3=ABC, 2=AB, 1=A,
							0=ABC)
							s = scroll (1=on, 0=off)
753E	-	753E	User Settings Flags	UINT16	bit-mapped	---g--nn srp--wf-	r = password for reset in use (1=on,
							0=off)
							p = password for configuration in use
							(1=on, 0=off)
							w = pwr dir (0-view as load, 1-view as
							generator)
							f = flip power factor sign (1=yes, 0=no)
			Full Scale Current (for load				If non-zero and user settings bit g is	1
753F	-	753F		UINT16	0 to 9999	none	set, this value replaces CT numerator
			% bargraph)				in the full scale current calculation.
7540	-	7547	Meter Designation	ASCII	16 char	none		8
							dddd = reply delay (* 50 msec)	1
7548	-	7548	COM1 setup	UINT16	bit-mapped	----dddd -0100110
							ppp = protocol (1-Modbus RTU, 2-
							Modbus ASCII, 3-DNP)
							bbb = baud rate (1-9600, 2-19200, 4-	1
7549	-	7549	COM2 setup	UINT16	bit-mapped	----dddd -ppp-bbb	38400, 6-57600)
754A	-	754A	COM2 address	UINT16	1 to 247	none		1
754B	-	754B	Limit #1 Identifier	UINT16	0 to 65535		use Modbus address as the identifier	1
							(see notes 7, 11, 12)
754C	-	754C	Limit #1 Out High	SINT16	-200.0 to +200.0	0.1% of full scale	Setpoint for the "above" limit (LM1),	1
			Setpoint				see notes 11-12.
							Threshold at which "above" limit	1
754D	-	754D	Limit #1 In High ThresholdSINT16		-200.0 to +200.0	0.1% of full scale	clears; normally less than or equal to
							the "above" setpoint; see notes 11-12.
754E	-	754E	Limit #1 Out Low SetpointSINT16		-200.0 to +200.0	0.1% of full scale	Setpoint for the "below" limit (LM2),	1
							see notes 11-12.
							Threshold at which "below" limit	1
754F	-	754F	Limit #1 In Low Threshold SINT16		-200.0 to +200.0	0.1% of full scale	clears; normally greater than or equal
							to the "below" setpoint; see notes 11-
							12.

5–6 EPM 6000 MULTI-FUNCTION POWER METERING SYSTEM – USER GUIDE