Show mac-address-table static Description | GE GE-DS-82, 82-POE

Chapter 6: Command Line Interface

show mac-address-table static Description:

Display static MAC address table entries.

show mac-address-table multicast Description:

Display multicast-related MAC address table.

smac-address-table static Description:

Set static unicast or multicast MAC address in secondary MAC address table. If multicast MAC address (address beginning with 01:00:5E) is supplied, the last parameter must be port-list. Otherwise, it must be port-id.

Syntax:

smac-address-table static <mac-addr><vlan-id><port-id port-list>

show smac-address-table Description:

Display secondary MAC address table entries.

show smac-address-table multicast Description:

Display multicast-related secondary MAC address table.

[no] filter Description:

Set MAC address filter. The packets will be filtered if both of the destination MAC address and the VLAN tag matches the filter entry. If the packet does not have a VLAN tag, then it matches an entry with VLAN ID 1.

Syntax:

[no] filter <mac-addr> <vlan-id>

178	GE-DS-82 and 82-PoE Ethernet Managed Switch User Manual

Image 182

GE GE-DS-82, 82-POE user manual Show mac-address-table static Description, Show mac-address-table multicast Description

Contents

Security N4131 Introduction ContentInstallation Web-Based Management Troubleshooting Switch Operation Power Over Ethernet OverviewWhat is PoE? Chapter Package Contents Product Description Remote and Centralize Management installation Powerful Security Power over Ethernet of GE-DS-82-PoE How to Use this ManualProduct Features Physical Port Priority queues on all switch ports Traffic classification Layer 2 FeaturesQuality of Service GE-DS-82-PoE Management MulticastSecurity Dram Product SpecificationsPower over Ethernet GE-DS-82-PoE Only LED Vlan Power over Ethernet PoE Standard Quality of ServiceAccess Control List PoE Power Supply Type Max. number of Class Standards Conformance Safety Power Pin AssignmentPoE Power Budget Standards Compliance 10/100Mbps TP Interface GE-DS-82, GE-DS-82-PoE Switch Front PanelHardware Description Gigabit TP Interface Reset buttonLED Indications Gigabit SFP Slots Per 10/100/1000Base-T port/SFP interfaces SystemPer 10/100Base-T RJ-45 port Switch Rear Panel Per 10/100Base-TX, PoE interfaces Port-1 to Port-8 Power Notice Console Port Switch Installation Desktop/Shelf Installation Rack-mount Installation Secure the brackets tightly, but do not over tighten screws SFP Transceiver Installation Mounting the GE-DS-82 in a rack Approved GE Security SFP Transceivers 1000Base-SX/LX SFP transceiver Connect the fiber cable Remove the transceiver module Pulling out the SFP transceiver Installation This chapter covers the following topics RequirementsSummary Management Access Overview Web Browser Management Management Methods Comparison PC / Workstation With IE Browser RJ-45/UTP-Cable IP Address Web Browser SetupLogin to the managed Switch Login screen PC / Workstation With Snmp application Administration ConsoleSNMP-Based Network Management IP Address Direct Access PC connected to Switch with RS-232 serial cable Virtual Terminal Protocols Telnet SetupProtocols Log on to the Console New Connection dialog window Snmp Protocol Management Architecture Web-Based Management About Web-based Management Requirements Logging on to the Switch Http//192.168.0.100 Main Web Panel Display Main Menu Port states are illustrated as follows System System Information This page includes the following fields Misc ConfigBasic Mode Object DescriptionBroadcast Storm Filter How do I get one for this box? IP ConfigurationWhat is an IP address? IP Configuration Objectdescription Subnet Mask Snmp ConfigurationSnmp Overview Gateway Snmp Community System Options System Contact System NameSystem Location Snmp Status Trap Managers Community strings serve as passwords. See the table belowCommunity Strings Community Enter the community string for the trap station SNMPv3 GroupsEnter the IP address of the trap manager Group Name View Name SNMPv3 ViewSecurity Name Included Excluded View Mask Hexadecimal SNMPv3 AccessView Subtree Digits SNMPv3 usm-user This page include the following fields Firmware UpgradeTftp Firmware Upgrade Click System then Web Firmware Upgrade Http Firmware UpgradeTo open the Firmware Upgrade screen, do the following Firmware Upgrade screen is displayed as in Figure Configuration Backup Tftp Restore Configuration Tftp Backup Configuration Configuration Backup interface Reboot the switch. Click reboot to reboot the system Factory DefaultSystem Reboot This page includes the following settings Syslog SettingPort Configuration Port Control Port Control interface BSF Port Status Port Statistics Tx Bad Packet Port Port number Link Status of linking-Up or Down StateOr receive any packet Via this port Port Sniffer Port Mirror application Sniffer Type Monitored Port Protected Port Protected Vlan Configuration Vlan Overview Web-Based Management 802.1Q Tag Static Vlan Configuration Port-Based Vlan Static Vlan interface Create a Vlan and add member ports to it Port-based Vlan interface Port Vlan NameGroup ID Member Tagged Understand nomenclature of the Switch802.1Q Vlan Untagged Vlan Group Configuration Vlan Group Configuration Vlan Group Configuration interface Vlan ID UnTag Member Vlan Filter Pvid Ieee 802.1Q Tunneling Q-in-Q Ingress Filtering In-Q Port Setting QinQ Vlan \ QinQ Port Setting screen in appears In-Q Tunnel Setting Object In-Q Tunnel Setting interface Gvrp Setting To configure Gvrp Enable global Gvrp function Object Description Gvrp Gvrp Table Object Description Vlan ID Rapid Spanning Tree Theory Bridge Protocol Data Units Creating a Stable STP Topology STP Port States Illustration of STP STP Port State Transitions This example, only the default STP values are used Before Applying the STA Rules STP Operation Levels Default ValueSTP Parameters Parameter Description 128 Rstp System ConfigurationParameter Description Default Value Port Priority Protocol Version Rstp modeForward Delay Time RSTP, 802.1w Root Bridge Information Rstp Bridge Status page screenshot Rstp Port Configuration interface Costs on the least cost path to the Root Bridge Admin Non STP Admin P2PAdmin Edge Path Cost Trunking Recommended STP Path Cost Range Aggregator Setting Lacp Aggregator InformationSystem Priority Work ports Assigning 2 ports to a trunk group with Lacp disabled Trunk group Lacp enabledSwitch 1 configuration Switch 2 configuration Switch 2 configuration interface Switch 1 Aggregator Information State Activity Forwarding and Filtering Dynamic MAC Table MAC Table Entries You can add static MAC address in the switch MAC table hereStatic MAC Table Add the Static MAC Address MAC Filtering Vlan ID for the entry MAC Filtering interface MAC Address Enter the MAC address that you want to filter Igmp Snooping About the Internet Group Management Protocol Igmp Snooping Multicast flooding Igmp Versions 1 Octets Type Response Time Igmp Querier Igmp State Transitions Igmp Configuration Will be displayed in Igmp status section QoS Configuration Understand QOS 802.1Q Tag and 802.1p priority QoS ConfigurationPriority Queue Service settings All High before Low First Come First ServiceWeighted Round Robin 802.1p priority QoS PerPort Configuration TOS/DSCP TOS MBZ TOS/DSCP ConfigurationPrecedence DiffServ Dscp TOS/DSCP Port ConfigurationObject Description TOS/DSCP Access Control List QoS Configuration TOS/DSCP Port Status Action Object Description Default ValueIPv4 ACL Packet Type TCP Ether Type Non-IPv4 ACLPacket Type/Binding box should select Non-IPv4 Type Binding Port Id MAC Limit MAC Limit ConfigurationMAC Limit Limit MAC Limit Port Status This table displays current MAC Limit status of each port 802.1X Configuration Understanding Ieee 802.1X Port-Based Authentication 802.1x device role 125 EAP message exchange System Configuration System information \ Misc Configuration\ 802.1x Protocol On the Radius Server 802.1x Port ConfigurationShared Key NAS, Identifier Set the identifier for the Radius client 802.1x Per Port Setting interface Misc Configuration Power Management Power Over EthernetPower over Ethernet Powered Device PoE Configuration Power Allocation PoE Temperature UnitPower limit mode PoE PSU Status Power Limit PD Classifications To configure Dhcp Relay Dhcp Relay and Option Lldp Use this page to change Lldp parameters Lldp ConfigurationPerPort Configuration Value is Lldp Per Port Configuration Lldp Status Login in to the Console Interface Console Management GE-DS-82-PoEConsole Login screen Configure IP address Show the current IP address Configure IP address Subnet Mask Gateway Exec Commands LevelFollowing table lists the CLI commands and description 144 Operation Notice Switch# configureSwitch config # Command Help System CommandsCommand Line Editing Key Function Syntax Switch Static ConfigurationPort Configuration and show status Parameters Port priority disable low high port-list Enable or disable port flow controlPort flow enable disable enable disable port-list Set port effective ingress or egress rate Port jumboframe enable disable port-list Port-id specifies the port to be shown Show protected port information Show trunking information Trunk ConfigurationTrunking Commands Lacp Commands Syntax Lacp system-priority Parameters Syntax Show lacp port port-idParameters Virtual LANsShow Lacp information by port Port-idspecifies the port to be shown Vlan Mode Port-based Display the current Vlan mode Disabled port-based dot1q specifies the Vlan mode Advanced 802.1Q Vlan ConfigurationChange Vlan mode Ingress filters configuration Delete Vlan entry Add or edit Vlan entrySyntax Vlan add 1-4094 Name cpu-portno-cpu-port List List Show Vlan entry information Specifies the Vlan id, null means all valid entries. e.g Vlan Syntax Show vlan pvid List Parameters Show port default Vlan idShow static Vlan entry information 162 Syntax Show vlan filter List Parameters Show Vlan filter settingSet ingress filter rules Forward Mac-age-time Parameters Misc ConfigurationNo mac-age-time Description Collision-Retry setting Syntax Collision-Retry off 16 32 Parameters Syntax Hostname name-str Parameters Administration ConfigurationChange Username / Password No hostname Syntax Ip default-gateway ip-addr User can configure the IP setting and fill in the new valueSet the default gateway IP address Show IP address, subnet mask, and the default gateway Set switch as dhcp client, it can get ip from dhcp server Reboot switchReset to Default Show dhcp enable/disable Copy tftp running config flash Description Tftp Update FirmwareRestore Configure File Download firmware from Tftp server Ip-addr specifies the IP address of the Tftp server Backup Configure FileCopy running config flash tftp Description Syntax Mac-limit port-list No mac-limit DescriptionMac-limit Description Show port monitoring information Port Mirroring ConfigurationSyntax Mirror-port rx tx both port-idport-list Parameters Quality of Service Set 802.1p priority Syntax Port priority disable 0-7 port-list Parameters Per Port Priority No mac-address-table static mac-addr Description MAC Address ConfigurationMac-address-table static Description Syntax No mac-address-table static mac-addrvlan-id Smac-address-table static Description Show mac-address-table static DescriptionShow mac-address-table multicast Description Show smac-address-table multicast Description Syntax Spanning-tree forward-delay 4-30 Parameters STP/RSTP CommandsSpanning-tree forward-delay Description Spanning-tree hello-time Description Spanning-tree priority Description Spanning-tree maximum-age DescriptionSyntax Spanning-tree maximum-age 6-40 Parameters Syntax Spanning-tree priority 0-61440 Parameters Spanning-tree debug Description Show spanning-tree port DescriptionSyntax Show spanning-tree port port-list Parameters No spanning-tree port mcheck Description Spanning-tree protocol version DescriptionSyntax Spanning-tree protocol-version stp rstp Parameters Syntax No spanning-tree port mcheck port-list Parameters Spanning-tree point-to-point mac Description No spanning-tree port non-stp DescriptionSyntax No spanning-tree port non-stp port-list Parameters Show snmp status Description System OptionsSnmp /no snmp Description Snmp system-name Description Snmp system-contact Description Snmp system-location DescriptionSyntax Snmp system-location location-str Parameters Syntax Snmp system-contact contact-str Parameters Delete Snmp community string Community StringsSet Snmp community string Syntax No snmp community community-str Parameters Remove trap receiver IP address and port number Trap ManagersSyntax Snmp trap ip-addr community-str 1..65535 Parameters Syntax No snmp trap ip-addr 1..65535 Parameters Syntax No igmp CrossVLAN Syntax No igmp fastleaveSyntax No igmp querier Show Igmp snooping information Enable/disable Igmp snooping debugging outputSyntax No igmp debug Syntax Show igmp status router groups table Parameters Radius-server host Description 802.1x ProtocolDot1x Description Radius-server key Description Syntax Dot1x timeout tx-period 0..65535 Parameters Syntax Dot1x timeout quiet-period 0..65535 ParametersDot1x timeout tx-period Description Radius-server nas Description Dot1x timeout radius-server Description Dot1x timeout supplicant DescriptionSyntax Dot1x timeout supplicant 1..300 Parameters Syntax Dot1x timeout radius-server 1..300 Parameters Show 802.1x per port information Set 802.1x per port informationSyntax Dot1x port fu fa au no port-list Parameters Ipv4 ACL commands Syntax No acl 1-220 Parameters Show ACL group information Acl addedit 1-220 permitdeny 0-4094 ipv4 0-255 Description Add or edit ACL group for Ipv4 Acl addedit 1-220 qosvoip 0-4094 Description Non-Ipv4 ACL commandsCommands Add or edit ACL group for non-Ipv4 SIP/SMAC binding commands Binding Syntax Bind add 1-220 Abcdef 0-4094 A.B.C.D 1-26 Parameters Show Binding group informationAdd Binding group Command Level Power over Ethernet Commands GE DS-82-PoEShow System Power over Ethernet information Global Configuration Example Syntax Show poe status port-list Parameters Global ConfigurationShow per PoE port information Poe temperature-protection enablex4 Description Configure PoE Over Temperature ProtectionConfigure PoE System Configure System PoE power limit mode information No Limit Configure PoE -- Port Enabling or disabling the port POE injects function Syntax Poe priority Critical High Low port-list Parameters Poe maximum-power Description 208 Forwarding & Filtering Address TableLearning Store-and-Forward Auto-Negotiation Power Over Ethernet Overview What is PoE? How Power is Transferred Through the Cable PoE System Architecture References When to install PoE?Consider the following scenarios PoE Provision Process Stages of powering up a PoE linkMicrosemi /PowerDsine Linear Tech Start-up Line DetectionClassification Operation DC Disconnect Power OverloadsPower Disconnection Scenarios AC Disconnect Why the Switch doesnt connect to the network? Solution Link LED is not lit SolutionPerformance is poor Solution Switch does not power up Solution While IP Address be changed or forgotten admin password Switchs RJ-45 Pin Assignments 1000Mbps, 1000Base T Tx + transmit Rx + receive Tx transmit Rx receive Not used 10/100Mbps, 10/100Base-TXStandard cable, RJ-45 pin assignment Side Straight CableSide SIDE2 Crossover Cable