Genicom GEK 00031B manual 223

Set Horizontal Pitch <DECSHORP>	219
Set Horizontal Spacing <SHS>	244
Set Horizontal Tab Stops <DECSHTS>	220
Set Left and Right Margins <DECSLRM>	222
Set Lines per Physical Page <DECSLPP>	221
Set Top and Bottom Margins <DECSTBM>	223
Set Vertical Pitch <DECVERP>	228
Set Vertical Spacing <SVS>	248
Set Vertical Tab Stops <DECSVTS>	226
Soft Terminal Reset <DECSTR>	225
Spacing Pitch Increment <SPI>	246
Tab Clear <TBC>	249
Vertical Position Absolute <VPA>	249
Vertical Position Backward <VPB>	250
Vertical Position Relative <VPR>	250
Vertical Tab Set <DECVTS>	229
Control characters
<CSI> Control sequence introducer	201
<DCS> Printer control string	201
<EPA> End of protected area	201
<ESA> End of selected area	201
<HTS> Horizontal tab set	202
<IND> Index	202
<NEL> Next line	202
<PLD> Partial line down	202
<PLU> Partial line up	202
<RI> Reverse index	202
<SS2> Single shift 2	202
<SS3> Single shift 3	202
<ST> String terminator	202
<VTS> Vertical tab set	202
Control codes	199
<BEL> Bell	199
<BS> Backspace	199
<CAN> Cancel	199
<CR> Carriage return	199
<ESC> Escape	199
<FF> Form feed	199
<HT> Horizontal tab	200
<LF> Line feed	200
<SI> Shift in	200
<SO> Shift out	200
<SUB> Substitute	200
<VT> Vertical tab	200
Horizontal advance increments	254
Page coordinate system	251
Character cell model	252
Origin and extent	252
Point model	252
Positioning and movement	253
Printable characters	198
Sixes graphics	256
printer emulation	8
Printronix 300/600	66
Printronix P300/600
Control Codes	66
<ACK> Line at 8lpi	66
<BS> Elongated Character Line	66
<CR> Carriage Return Slew Zero or Edit Mode . 66
<DC1> Ready/Select	66
<DC3> Busy/Select	67
<DLE> High vertical density graphics	67

<ENQ> Normal density plot line	67
<EOT> High density plot line	67
<ETX> End of transmission	67
<FF> Form Feed	67
<HT> Horizontal Tab	67
<LF> Line Feed	67
<RS> Record Separator	67
<SI> Shift In	68
<SO> Shift Out	68
<SP> Space	68
<UNDL> Underline	68
<US> Unit Separator	68
<VT> Vertical Tab	68
Bell code <BEL>	66
Control Codes<DEL> Delete	67
Electronic Vertical Format Unit	72
Graphics	69
Dot Patterns	70
Dot Patterns and Densities	69
Printronix P300/600 Emulation Options Table	274
Printronix Pseries Emulation Options Table	274
Proprinter
Command Directory	111
Commands
<HT> Horizontal Tab	110
Automatic line feed	114
Deselect printer	117
Double strike print, start	115
Double wide print, on/off	118
Emphasized print, start	115
Emphasized print, stop	115
Form length in inches, set	115
Graphics, high-speed double density, set	120
Graphics, low speed double density, set	120
Graphics, quadruple density, set	121
Graphics, set normal density	120
Horizontal margins, set	118
Horizontal tab stops, set	115
Overscore	112
Print continuously from all character chart	112
Print mode, select	116
Print single character from all character chart....	112
Proportional spacing, set	117
Select character set 1	114
Select character set 2	114
Select code page	113
Set 12 cpi	112
Set 7/72 line spacing	113
Set 8 lpi	113
Set form length in lines	115
Set graphics line spacing	114
Set top of form	114
Skip perforation, cancel	116
Skip perforation, set	116
Start text line spacing	113
Store 7/72 line spacing	114
Superscript / Subscript, reset	117
Superscript / Subscript, Set	117
Tabs, power on settings, set all	117
Underscore	112
Unidirectional printing, set	117
Variable line feed	116

GEK-00029B 313 5000 Series Programmer’s Manual