Stand | Grizzly G0555 specification

202

201

	Stand
	205	206
	204	206
	204	207
		208
	211
	212

212 211 213

209

210

REF	PART #	DESCRIPTION

201	P0555201	STAND TOP (G0555)
201	P0555P201	STAND TOP (G0555P)
202	PCB06M	CARRIAGE BOLT M8-1.25 X 16

204	PFN01M	FLANGE NUT M8-1.25

205	P0555205	STAND SIDE (G0555)

205	P0555P205	STAND SIDE (G0555P)
206	PB83M	HEX BOLT M6-1 X 16
207	PW03M	FLAT WASHER 6MM

REF	PART #	DESCRIPTION

208	PFN02M	FLANGE NUT M6-1
209	P0555209	UPPER STAND BRACE (G0555)
209	P0555P209	UPPER STAND BRACE (G0555P)

210	P0555210	LOWER STAND BRACE (G0555)

210	P0555P210	LOWER STAND BRACE (G0555P)

211	PN08	HEX NUT 3/8-16
212	PW04M	FLAT WASHER 10MM
213	P0555213	STAND FOOT

-60-	Model G0555/G0555P (Mfg. Since 5/11)

Image 62

Grizzly G0555 owner manual Stand

Contents

Ultimate 14 Bandsaw Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification MaCHiNe data SHeet Table Information Safety Safety Instructions for MachineryPage Additional Safety for Bandsaws Full-Load Current Rating Power SupplyAvailability Circuit Information Grounding Requirements Shock Hazard Minimum Gauge Size 14 AWG Extension CordsVoltage Conversion 50 ft Unpacking SetupNeeded for Setup Description Qty Hardware Recognition Chart Inventory Shipping Inventory Figures Qty Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Assembly Ing the stand easier in a later step Leveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 Blade Center Tracking To center track the blade Dust Collection To connect a dust collection hose Disconnecting Power Power Connection Test RunConnecting Power To test run the machine Tensioning Blade To tension the bandsaw blade Adjusting Blade Support Bearings To adjust the support bearings Tool Needed Qty Adjusting Blade Guide BearingsTo adjust the upper and lower blade guides Page To set the positive stop 90˚ to the blade Table Tilt CalibrationTools Needed Qty Step Aligning TableTo align the table to the blade Aligning Fence Operations Operation Overview Before cutting, inspect all workpieces for the following Disabling & Locking SwitchWorkpiece Inspection To tilt the table To adjust the height of the guide postGuide Post Table Tilt Blade Speed To change the blade speed Blade Length Blade DimensionsBlade Information Blade Width Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage are Blade Removal Blade InstallationBlade Change Ripping Basic Cutting TipsCutting Options To make a rip cut CrosscuttingResawing To make a 90˚ crosscut Cutting Curves Stacked Cuts To complete a stacked cut Model AccessoriesBandsaw Blades G1928-Bandsaw Handbook G7315Z-Super Heavy-Duty Shop FOX Mobile Base H7584-Re-Saw Fence Retrofit Kit Schedule MaintenanceCleaning Protecting Daily To redress the rubber tires LubricationRedressing Rubber Tires Motor & Electrical ServiceTroubleshooting Cutting Operations Miscellaneous Tensioning V-Belt Belt TensionChecking V-Belt Tension To properly tension the V-belt To replace the V-belt Replacing V-BeltShimming Table Belt Tension subsection on Wheel Alignment Checking Wheel Alignment Shimming a Wheel To shim a wheel Upper Wheel Lateral Adjustment To adjust the upper wheel laterally To skew your fence Blade LeadTo correct blade lead To shift the table To reset the blade tensioner Blade Tensioner Fence Scale Calibration To calibrate the scale Wiring Wiring Safety Instructions Wiring Diagram 110 VAC Main Main Parts List Description Description Stand Fence Labels 144V2 216 155 145 148 147 149 157 156 218 217 214 Warranty Card Comments Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA Warranty and Returns Warranty and Returns Order Hours a DAY