Notching Station | Grizzly G0646, G0647 guide

Notching Station

��

��

��

��

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

137	P0646137	NOTCH PUNCH
138	P0646138	CAP SCREW M20-2.5 X 90
139	P0646139	NOTCH SIDE DIE
140	P0646140	NOTCH END DIE
141	P0646141	NOTCH BOLSTER
142	PSB64M	CAP SCREW M10-1.5 X 25
143	PSS21M	SET SCREW M8-1.25 X 25

REF	PART #	DESCRIPTION

144	P0646144	NOTCH BOLSTER CLAMP
145	PLW05M	LOCK WASHER 12MM
146	PW06M	FLAT WASHER 12MM
147	PB12M	HEX BOLT M12-1.75 X 55
148	PSB64M	CAP SCREW M10-1.5 X 25
149	P0646149	TEE NUT M12-1.75

G0646/G0647 50/65 Ton Ironworker

-67-

Image 69

Grizzly G0646, G0647 owner manual Notching Station

Contents

50/65 TON Ironworker Page Table of Contents Introduction Foreword Functional OverviewContact Info Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Power Connection Device Power Supply Circuit RequirementsCircuit Requirements 220/440V Operation 440V Conversion To rewire the Model G0646/G0647 for 440V operation Setup Safety SetupItems Needed for Setup Unpacking Inventory Figure Qty Inventory Clean Up Site Considerations Placement LocationMoving & Placing Base Unit Floor Load Using Machine Mounts Mounting to Shop FloorBolting to Concrete Floors To test run the machine Test Run Factory adjustments that should be verified Recommended Adjustments Operation Safety OperationsBasic Controls Operation Tips Using the Punching StationPunching Motor Stop Button Turns the motor OFF Removing/Installing Punch Tooling Tools Needed QtyTo remove punch tooling Punch, adapter, retaining ring, Die installed To install punch tooling Bolster Mounting Hex Bolts 4 shown Using the Notching Station Removing & Installing Notch DiesNotching Notch Die Clearances To install the notch diesPage To avoid tooling or workpiece breakage Flat Stock Shearing To shear flat stock To shear bar stock Bar Stock Shearing Extension Bar Angle Iron ShearingMaking a 90 Cut Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication Accessories H7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 GalT20448T20452 T20501 T20456 H0736 Available Tooling Maintenance Cleaning ProtectingSchedule Shearing Hold-Down Adjustment Rod LubricationBeam Pivot Shaft Support Frame Lubrication Hydraulic System Filling Hydraulic ReservoirFluid Capacity Draining & Re-Filling Hydraulic ReservoirTo drain and re-fill the hydraulic reservoir To align the beam Beam Alignment Service TroubleshootingMotor & Electrical Operations To remove and replace the flat stock shearing dies Flat Stock Shearing Dies To remove the angle iron shearing dies Angle Iron Shearing Dies To remove and replace the bar stock shearing dies Bar Stock Shearing Dies Disconnect Machine from Power Shearing Table Alignment To reset the position of the limit rings Limit RingsHydraulic Fluid Pressure Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Limit switch wiring Electrical Components Wiring Diagram Motor wiring G0646/G0647 50/65 Ton Ironworker Motor Wiring Diagram Hydraulic System Overview Parts Description G0646 Upper Front-Half Parts List G0647 Upper Front-Half Parts List Half Upper G0646 Upper Rear-Half Parts List Description G0647 Upper Rear-Half Parts List Cabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns