Symbology Specifications | Hand Held Products 800, 600 specification

Symbology Specifications

Symbology	Parameters (defaults are in bold)
EAN/UPC	Enable: On or off
	Magnification factor: (080/085/090/100/105/110/115/120/130/140/150/
	160/180/200)
	Expand U.P.C.-EO: Yes or No
Code 39	Enable: On or off
	Check Character: None or Checked
	Fixed W/N: None or a value between 1.4 and 3.9 + 0.2
Interleaved	Fixed Msg Len*: None or a value between 1 and 49 characters
2 of 5	Enable: On or off
	Check Digit: None or Checked
	Fixed W/N: None or a value between 1.4 and 3.9 + 0.2
Code 128	Fixed Msg Len*: None or a value between 1 and 78 digits
	Enable: On or off
Code 93	Modes Shown? Yes or No
	Fixed Msg Len*: None or a value between 1 and 70 characters
	Enable: On or off
Codabar	Fixed Msg Len*: None or a value between 1 and 80 characters (from
	Code 39 set)
	Enable: On or off
	Character Font & Tolerances: Trad’l,”USS” or ISO/IEC’83
Code 11	Fixed W/N: None or a value between 1.4 and 3.9 + 0.2
	Fixed Msg Len*: None or a value between 1 and 61 digits
	Enable: On or off
	1 or 2 check digits
	Fixed Msg Len*: None or a value between 1 and 80 digits
Code 16K	Enable: On or Off
	Modes Shown? Yes or No
	Fixed Msg Len*: None or up to 154 characters, full symbol
Code 49	Enable: On or Off
	Fixed Msg Len*: None or up to 49 alpha (81 numeric characters, full
	symbol
MSI Code	Enable: On or Off
	User Check: None, Mod 10 or Mod 11
	Fixed Msg Len*: None or a value between 1 and 50 digits
IATA 2 of 5	Enable: Yes or No
Regular 2 of 5	Enable: Yes or No
	Enable: Checked or None

*The message length specification for each symbology is listed. Although you can enter any value between 0 and 255, the unit does not decode more than the values indicated by the specification.

Quick Check® 600/800 Series User’s Guide

3 - 3

Image 27

Hand Held Products 800, 600 manual Symbology Specifications, Symbology Parameters defaults are in bold

Contents

User’s Guide Disclaimer For European Community UsersWaste Electrical and Electronic Equipment Information Table of Contents Reviewing Scan Data Saving and Printing Chapter Customer Support About This Guide Getting Started SymbolDescription Power or Select or ↑, ↓, ←, → Unpacking the Quick Check 600/800 VerifierTerm in manual Term in software Quick Check 600/800 Verifier Noting the Verifier’s Features EAN/UPC Buttons Special FeaturesDisplay LEDs Ports Specifications Installing the BatteriesSpecification To Install the Batteries Charging the BatteriesTo charge the batteries To turn on the unit Turning the Unit On and Off No Printer Attached, then refer to .a Quick Check 600/800 Series User’s Guide Calibrating the Quick Check 600/800 Verifier To turn off the unitTo calibrate the Quick Check 600/800 Verifier To scan properly using a pen wand To scan properly using a mouse wandProperly Scanning With the Unit Cleaning the Wand Accessories and OptionsItem/DescriptionOrder code Documentation Quick Check 600/800 Series User’s Guide Quick Start Guide Print your scan results Review the option settings Changing the Settings Changing the SpecificationsSymbologies Symbologies Symbology Parameters defaults are in bold Symbology Specifications Modes Shown Magnification FactorExpand U.P.C./EO Check Options Character Translation Table Code 128, Code 16K, and Code Character Font & Tolerances → or Select To modify the symbology optionsWide-to-Narrow Ratio Fixed Message Length Industry Applications Changing the Test Criteria Scan GradeTo select an application Decodability ISO/IEC gradesNumber of Scans To return to the previous menu, press Power Changing the Scanning OptionsTo change the test criteria To change the scanning options Beeper PitchExtended Accuracy Decode Direction Changing the Output Options Display OptionsParameter Result Lines AutoPrint/Store Print Options Scan Profile To change the output optionsTo change the display options To change the printout options Resetting the Default SettingsLocking the Settings To reset a unit About Command Codes Using a Command Code Generic Code Selections C./EAN/JAN Enable On or Off Customized Command Codes Choosing a Command Code To use a customized Command Code To create a customized Command CodeTo request a Command Code from Hand Held Products Quick Check 600/800 Series User’s Guide Reviewing Scan Data Reviewing Scan ResultsScan Grades ISO/IEC Symbol Grade Determining the ISO/IEC Symbol Grade Quick Check 600/800 Series User’s Guide Reviewing a Scan Example To obtain the scan grade and ISO/IEC Symbol grade Quick Check 600/800 Series User’s Guide To review data from the last scan LED Display Bar growth LCD bar growth LED lit Tolerance used Indication Audio Sounds Parameter Result Reviewing the Dimensional ParametersErrors in Dimensional Parameters Parameter Trad’l Calculating To review the dimensional parameters Reviewing the Reflectance Parameters PCS Errors in Reflectance Parameters To review the reflectance parameters Symbol Contrast, Minimum and Maximum Reflectance Reviewing the Format Parameters Errors in Format Parameters Reviewing Messages To review the format procedures Using Sstr Codes to Review Data Sstr CodesSstr Code Type Test Criteria Name To customize the result display Using the Quick Check Verifier as a ReflectometerTo quickly review data using Sstr Codes To return the customized display to the default display To use the Quick Check Verifier as a static reflectometer To save scan data Saving and PrintingSaving Data Checking the Print Buffer During Operation To print current data Printing DataTo check the print buffer during operation To clear delete the records stored in the memory, press → Deleting Stored Data To print stored dataTo stop printing Interfacing With a Computer Reviewing the PrintoutsTo delete stored data QCP and Qchsp Printouts Printing Guidelines Using the QCP or Qchsp Switch Position Function To set up the QCP or Qchsp To install or replace the QCP or Qchsp paper rollTo turn on and off the QCP or Qchsp To remove the ribbon from the QCP or Qchsp To perform a QCP or Qchsp self-test Troubleshooting the QCP or Qchsp Quick Check 600/800 Series User’s Guide General Bar Code Information Background Information Symbology Industries Organization Symbology Specifications GS1 formerly UCC and EAN Symbology Characteristics Quick Check 600/800 Series User’s Guide Symbology Character Set Widths How a Bar Code Verifier WorksElement Additional Information Quick Check 600/800 Series User’s Guide SYM Identifier Code Using DataMatchUnderstanding the DataMatch Feature Downloading DataMatch Structuring and Loading the Database To load the database into the verifier Decode Quick Check 600/800 Series User’s Guide To select DataMatch Selecting the DataMatch Feature Reviewing DataMatch Results Quick Check 600/800 Series User’s Guide General Operation Using a Quick Check 800 Verifier Percent Decoded/Scanned Mode Reflectance-Based InformationScanProfile Output Print Results Calculate Decoded/Scanned Change Settings Change Settings Test Criteria #Scans/Symbol nnn Type Display Message Printout Message Error, Application, and Type Messages Database ECV /VCVS Bookland Quick Check 600/800 Series User’s Guide Ccbba Hibcc EAN ITF SCS /ITF EAN SCS Quick Check 600/800 Series User’s Guide Flow Charts Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Quick Check 600/800 Series User’s Guide Sstr Codes Quick Check 600/800 Series User’s Guide Special Codes Quick Check 600/800 Series User’s Guide Unrecognized Symbols Unrecognized Symbols Quick Check 600/800 Series User’s Guide To check the software version TroubleshootingTo restore the display Customer Support Latin America Limited Warranty Quick Check 600/800 Series User’s Guide Page Hand Held Products, Inc