Harman-Kardon AVR 745 LFE Low-Pass-FilterSetting, Sub Mode Setting, System Configuration, Figure

29510_AVR745_Engelsk 30/10/06 9:32 Side 37

System Configuration

*	S P E A K E R S I Z E		*
→ F L / F R		: S M
C E N T E R		: S M
S L / S R		: S M
S B L / S B R		: S M
L F E	L P F L T	: 1 0 0 H z
S U B	M O D E	: S U B L / R + L F E
N O .	S U B S	: 2
S U B	S I Z E	: 1 0 i n / 2 5 0 m m

E Z S E T S E T T I N G S : O F F O N

B A C K T O M A N U A L S E T U P

Figure 27

To change the setting for any of the four speaker positions, press the ⁄/¤ Navigation Button DF until the cursor points to the line where you wish to make the change. Press the ‹/› Navigation Button DF to change the set- ting, but note that when you do this for the first time in the menu, a warning message (Figure 28) will appear in the on-screen display reminding you to rerun EzSet/EQ II after you are finished with any speaker configuration changes. This is necessary to make any level output adjustments needed after the setting changes so that the new configuration will be properly integrated.

W A R N I N G ! !

C h a n g e s d o n e t o t h e s e s e t t i n g s w i l l a f f e c t

E Z S E T / E Q p e r f o r m a n c e . I f a n y c h a n g e s a r e n e e d e d

p l e a s e r e - d o E Z S E T / E Q . O t h e r w i s e p r o c e e d w i t h a d j u s t m e n t .

B A C K T O S P E A K E R S I Z E

Figure 28

The warning message will remain for four sec- onds and then the SPEAKER SIZE menu will return to the screen. At this point you may change the settings to the “size” or crossover for any of the four speaker positions using the Navigation Buttons DF as shown above. The information below details the settings avail- able for each of the speaker configurations.

At each of the four speaker position lines, you have the option to set the speaker size and crossover. Note that the “size” does not refer to the speaker’s actual physical size, but rather to the ability of the speaker to reproduce low-fre- quency information. If your speakers at any posi- tion are traditional full-range models capable of handling the full audio spectrum, select LARGE. These speakers are called “large” since the low-frequency drivers required to play bass without strain or distortion are typically eight to fifteen inches in diameter, in turn making the speaker cabinet larger than those with small (or no) low-frequency drivers. When the speakers at a particular position are smaller frequency-lim- ited speakers that do not have the ability to properly reproduce low-frequency sounds, select

SMALL.

At all speaker positions except for the front left/right speakers, you may also select NONE. This setting tells the system that no speakers are present at that position, allowing the AVR to select the correct surround modes that are com- patible with the number of speakers installed. For example, in order to use the Dolby Digital EX, Dolby Pro Logic IIx, DTS-ES, Logic 7/7- channel and “7 Stereo” modes, you must have either LARGE or SMALL speakers entered as the setting for the BACK SURR channels.

When LARGE is selected for any channel, a full-range signal will be sent to the speaker out- puts for that channel. For all speaker positions except the front left/right, when LARGE is cho- sen, no derived sound will be sent to the sub- woofer output, although in all cases the special low-frequency effects (LFE) signals available on

5.1or 6.1 digital programs will always be sent to the subwoofer output.

When SMALL is selected for any channel, you may also enter a setting for the crossover fre- quency at which sound is divided between the frequency above which sound is sent to the channel’s speakers and below which sound is sent to the subwoofer. When configuring a “small” speaker, choose the setting that has the frequency closest to that of the lowest frequency the speakers in question are capable of handling. If one of the six available crossover points does not match, select the one that is above, but clos- est to, the speaker’s low-frequency limit.

When there are no speakers available at a specif- ic position, select NONE. When this option is chosen for the Center or Side Surround speakers, the sound that would normally be sent to these channels will be split between the front left and right speakers. Note that when your system does not include Center or Surround speakers, the use of Dolby Virtual Speaker as a surround mode may provide a sound field that simulates the presence of these speakers. (See page 42 for more infor- mation on the Dolby Virtual Speaker mode.)

Note that when NONE is selected for the Back Surround speakers, the 6.1/7.1 channel surround modes are not available. When this is the case for your system you may wish to take advantage of the availability of the unused amplifier channel pair to power a second set of speakers in another room. See page 55 for more information on amplifier configuration.)

Once any desired changes have been made to the speaker size and/or crossover, press the ⁄/¤ Navigation Button DF to move the cursor to any other line on this menu to make a setting change, or go to the BACK TO MANUAL SETUP menu and then press the OK/Enter Button E on the TC 30 or the Set Button Q to continue with overall configura- tion.

LFE Low-Pass-Filter Setting

The LFE LP FLT line selects the frequency setting below which sounds that may be avail- able from a special low-frequency effects (LFE) track are sent to the subwoofer. In most cases, this setting will be set accurately by EzSet/EQ but, should you wish to make a change from that setting or the 120Hz frequency that is most com- monly used in the creation of LFE channels by motion picture sound mixers, after making sure that the SPEAKER SIZE menu (Figure 27) is on the screen, press the ⁄/¤ Navigation Button DF so that the cursor is pointing to LFE LP FLT. Press the ‹/› Navigation Button DF to begin the selection process, and note that the warning message (Figure 28) will appear reminding you to rerun EzSet/EQ II after all changes have been made.

When the SPEAKER SIZE menu returns to the screen, press the ‹/› Navigation Button DF to make your selection. When the desired setting appears, press the ⁄/¤ Navigation Button DF to move the cur- sor to any other line on this menu where you wish to make a setting change, or go to the BACK TO MANUAL SETUP menu and then press the OK/Enter Button E on the TC 30 or the Set Button Q to continue with overall configuration.

Sub Mode Setting

When the Front Left/Right speakers are con- figured as “Large” and a subwoofer is detected by EzSet/EQ II or manually configured as being available, additional options are available to furt- her customize bass redirection. To change these settings, first make sure that the SPEAKER SIZE menu (Figure 27) is on the screen, and then press the ⁄/¤ Navigation Button DF so that the cursor is pointing to SUB MODE. Press the ‹/› Navigation Button DF to begin the selection process, and note that the warning message (Figure 28) will appear reminding you to rerun EzSet/EQ II after all changes have been made.

The following options are available:

•The default setting for Large front left/right speakers when a subwoofer is present is SUB L/R + LFE. In this mode, all sounds below the crossover point set on the LFE LP FLT line will be sent to BOTH the subwoofer and the front left/right speakers.

•To send only the LFE channel information to the subwoofer, but have all other (“derived”) low-frequency sounds sent to the front left/right speakers, select the SUB (LFE) setting.

ENGLISH

SYSTEM CONFIGURATION 37