29510_AVR745_Engelsk 30/10/06 9:32 Side 56
Multiroom Operation
Remember that once this setting is made you will not be able to take advantage of any of the 6.1/7.1- channel decoding or processing modes, and no Surround Back speakers must be selected in the speaker setup procedure outlined earlier. In addition the speakers used for the remote zone must be connected to the Surround Back/ Multiroom Speaker Outputs . The volume for these speakers is set by the multiroom sys- tem, as explained on page 55 of this manual.
Infrared Output Selection
The AVR 745 enables you to select which IR input will be used to feed the Full Carrier IR Output . The factory default setting is the IR signal that is fed to the Multiroom IR Input
, but you may select other options.
To change this setting, first make sure the
Eon the TC 30 or the Set Button Q on the ZR 10. Press the ⁄/¤ Navigation Buttons DF to select one of these options:
• ZR 10 feeds the signal present at the
Multiroom IR Input | to the Full Carrier |
IR Output . |
|
•
to the Full Carrier IR Output .
•FRONT feeds the signal received through the
the Full Carrier IR Output .
With the remote pointing toward an IR sensor or
Selector C or 
Selector to
turn the multiroom system on directly to a specific source. To turn the multiroom system on using the TC 30 remote, press the Devices Button 4 on the TC 30 remote and then press the Screen Button 6 next to AV RECEIVER. When the choices on the LCD Screen 7 change, press the Page Left/Right Buttons 8 once and then press the Screen Button 6 next to
When the multiroom system is turned on, you may use the same buttons on either remote that would normally be used to control an AVR function such as volume, source selection, tuner control or the operation of an iPod docked to The Bridge. If any of the input devices are connected to the IR Output or Full Carrier IR Output
,by either a
To turn the system off from the remote room, press the
To turn the
When the multiroom system is turned on, the input selected using the Multiroom Menu will be fed to the Multiroom Audio/Video Output
jacks on the rear panel as well as the
A-BUS Jack .
The volume will be as set in the same menu, although it may also be adjusted using an option- al IR sensor and the Zone II remote in the remote location or on the optional audio power amplifier connected to the Multiroom Output jacks .
Although changes to the input source or remote room volume will normally be made using an IR sensor in the remote room that is connected to the AVR, it is also possible to change those set- tings from the main listening room. This is useful for situations where some or all of the remote rooms do not have an IR sensor, or to take con- trol over the remote room without actually being in that room.
In addition to using the
When all needed adjustments to the MULTI- ROOM SETUP menu have been made, press the ⁄/¤ Navigation Buttons DF until the cursor is pointing to BACK TO MASTER MENU to make changes to other menus, or press the Menu Button A or the OSD Button E to exit the menu system and return to normal operation.
Multiroom Operation
When operating the AVR from a remote room location where an IR sensor link has been con- nected to the AVR’s rear panel Multiroom IR Input , you may use either the Main remote control or the ZR 10 remote buttons BCD. Press the AVR Selector B to turn the unit on to the last source, or any of the other Selector buttons to turn on to a specific source.
NOTE: When the tuner is selected as the source for the remote zone, any change to the frequency or preset will also change the station being lis- tened to in the main room, if the tuner is in use there. Similarly, if someone in the main room changes the station, the change will also impact the remote room.
To turn the multiroom system on from the room where the AVR 745 is located, press the Devices Button 4 on the TC 30 remote and then press the Screen Button 6 next to AV RECEIVER. When the choices on the LCD Screen 7 change, press the Page Left/Right Buttons 8 once and then press the Screen Button 6 next to
Eand then press the ⁄/¤ Navigation Buttons DF to turn the system on.
Using the TC 30 remote, press the Devices Button 4 on the TC 30 remote and then press the Screen Button 6 next to AV RECEIVER. When the choices on the LCD Screen 7 change, press the Page Left/Right Buttons 8 once and then press the Screen Button 6 next to
To change the remote room’s input source, when MULTI INPUT appears, press the OK/Enter Button E on the TC 30 or the Set Button Q on the ZR 10, and then press the
⁄/ ¤ Navigation Button DF until the desired input appears in the
56MULTIROOM OPERATION
