Securing and Leveling the Appliance | Heat & Glo LifeStyle 2137-900

C. Securing and Leveling the Appliance

WARNING

Fire Risk.

•Prevent contact with sagging, loose insulation.

•Do NOT install against combustible materials

such as exposed insulation, plastic and insulation backer.

The diagram shows how to properly position, level, and secure the appliance (see Figure 7.8). Nailing tabs are provided to secure the appliance to the framing members.

•Place the appliance into position.

•Level the appliance from side to side and front to back.

•Shim the appliance as necessary. It is acceptable to use wood shims.

•Bend out nailing tabs on each side.

•Keep nailing tabs ﬂush with the framing.

•Secure the appliance to the framing by using nails or screws through the nailing tabs and two holes in each end of outer non-combustible panel.

NAILING TABS

(BOTH SIDES)

Figure 7.8 Proper Positioning, Leveling and Securing of a

Appliance

WARNING

Fire Risk.

• ALWAYS maintain speciﬁed

clearances around the appliance.

• Do NOT notch into the framing around the appliance spacers.

Failure to keep insulation, framing or other material away from the appliance may cause ﬁre.

Heat & Glo • Soho24B • 2137-900 Rev. P • 8/12

21

Image 21

Heat & Glo LifeStyle 2137-900 Securing and Leveling the Appliance, Proper Positioning, Leveling and Securing of a

Contents

Model Soho24B What to do if you smell gasHot glass will cause burns Homeowner Reference Information Congratulations Table of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Installation to ensure maximum safety and beneﬁt Getting StartedTools and Supplies Needed Framing and Clearances Selecting Appliance LocationMantel Projections Clearances Constructing the Appliance Chase Termination Locations Vent Termination Minimum ClearancesSee .4 for speciﬁc clearances Inches U.S.A Covered Alcove Applications Vent Table Key Vent Information and DiagramsUse of Elbows Measuring Standards Top Vent Horizontal Termination One Elbow Vent DiagramsTwo Elbows Minimum Maximum V1 Min H1 Max V2 Min H2 Max Top Vent Horizontal Termination Three Elbows Top Vent Vertical Termination No Elbow V1 = 45 ft Max .72 m V1 = 3 ft Min mmV1 Minimum H1 Maximum V1 + V1 Minimum H1+ H2 Maximum V1+ V2 Minimum Top Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Pipe SLP Vertical Penetration Framing Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Top Vent Appliance Preparation Material Installation of Non-combustible Facing Material Proper Positioning, Leveling and Securing of a Securing and Leveling the Appliance Assemble Vent Sections Installing Vent Pipe Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Decorative Ceiling Components Assemble and Install Storm Collar Install Metal Roof Flashing Install Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination 17 Venting through the wall Install Horizontal Termination Cap Fuel Conversions Gas Connection Gas InformationGas Pressures Pressure Natural Gas Propane High Altitude Installations Electrical Information Recommendation for Wire GRN wire Ground attached To GRN screw with Inside box Junction Box Installation Finishing Facing MaterialSee for combustible/non-combustible deﬁnitions Painting Installation of Non-Combustible Facing Materials Clean the Appliance Appliance SetupAccessories Remove Shipping Materials Positioning Stones Stone Placement Soho24B No Stones in this Area Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass Assembly Before Lighting Appliance Operating Instructions Final inspection by Lighting Instructions IPI Frequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting IntelliFire Ignition SystemSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance Tasks Recommend addition of screen if one is not present Inspect Maintenance Tasks Appliance Dimensions Table Appliance Dimension DiagramReference Materials Location Inches Millimeter SL Series Components Vent Components Diagrams  B. Vent Components Diagrams Assembly 305 mm 356 mm 330 mm12-1/2 318 mm Stocked Service PartsAt Depot 24 x 24 Direct Vent Fireplace #11 IPI Valve Assembly No longer available SOHO24B-ONYX Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Contact Information