Vent Components Diagrams | Heat & Glo LifeStyle 2137-900 instruction

B. Vent Components Diagrams

	SL Series Components
	13-7/8 in.	9-1/2 in.
	(352 mm)	(241 mm)
	14 in.
	(356 mm)
	DRC-RADIUS
	Cap Shield
	11-5/8 in.
	(295 mm)
	7-1/8 in.	12-1/8 in.
	7-1/8 in.	(308 mm)
	(181 mm)	(308 mm)
	(181 mm)
	5-3/4 in.
	(146 mm)
	COOL-ADD
		Cap Shield
	Figure 16.1 SLP Series Vent Components
46	Heat & Glo • Soho24B • 2137-900 Rev. P • 8/12

Image 46

Heat & Glo LifeStyle 2137-900 owner manual Vent Components Diagrams, SL Series Components

Contents

What to do if you smell gas Model Soho24BHot glass will cause burns Congratulations Homeowner Reference Information Table of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Selecting Appliance Location Framing and ClearancesMantel Projections Constructing the Appliance Chase Clearances Vent Termination Minimum Clearances Termination LocationsSee .4 for speciﬁc clearances Covered Alcove Applications Inches U.S.A Use of Elbows Vent Information and DiagramsVent Table Key Measuring Standards Two Elbows Vent DiagramsTop Vent Horizontal Termination One Elbow Minimum Maximum Top Vent Horizontal Termination Three Elbows V1 Min H1 Max V2 Min H2 Max V1 = 45 ft Max .72 m V1 = 3 ft Min mm Top Vent Vertical Termination No ElbowV1 Minimum H1 Maximum V1 + Top Vent Vertical Termination Three Elbows V1 Minimum H1+ H2 Maximum V1+ V2 Minimum Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Vertical Penetration Framing Pipe SLP Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Appliance Preparation Top Vent Installation of Non-combustible Facing Material Material Securing and Leveling the Appliance Proper Positioning, Leveling and Securing of a Installing Vent Pipe Assemble Vent Sections Assemble Slip Sections Secure the Vent Sections Install Decorative Ceiling Components Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install Decorative Wall Components Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap 17 Venting through the wall Gas Pressures Gas InformationFuel Conversions Gas Connection Pressure Natural Gas Propane High Altitude Installations Recommendation for Wire Electrical Information Junction Box Installation GRN wire Ground attached To GRN screw with Inside box Facing Material FinishingSee for combustible/non-combustible deﬁnitions Installation of Non-Combustible Facing Materials Painting Accessories Appliance SetupClean the Appliance Remove Shipping Materials Stone Placement Soho24B Positioning Stones No Stones in this Area Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass Assembly Operating Instructions Before Lighting Appliance Lighting Instructions IPI Final inspection by Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit IntelliFire Ignition System TroubleshootingSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintenance Tasks Maintaining and Servicing Appliance Inspect Maintenance Tasks Recommend addition of screen if one is not present Reference Materials Appliance Dimension DiagramAppliance Dimensions Table Location Inches Millimeter Vent Components Diagrams SL Series Components  B. Vent Components Diagrams Assembly 12-1/2 356 mm 330 mm305 mm 318 mm At Depot Service PartsStocked 24 x 24 Direct Vent Fireplace #11 IPI Valve Assembly SOHO24B-ONYX No longer available Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Contact Information