Appliance Setup, Accessories | Heat & Glo LifeStyle 350TRSILP-AUF

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 9.E.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of ap- proved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

DO NOT MODIFY THIS APPLIANCE

64	Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12

Image 64

Heat & Glo LifeStyle 350TRSILP-AUF owner manual Appliance Setup, Remove Fixed Glass Assembly, Remove the Shipping Materials

Contents

Models 350TRSI-AUF 350TRSILP-AUF What to do if you smell gasDo Discardnot Hot glass will cause burns Models 350TRSI-AUF, 350TRSILP-AUF Congratulations Homeowner Reference Information Sans Compliance Novida Testing ServiceSans Table of Contents User Guide Appliance Setup TroubleshootingFinishing Reference Materials Australian Warranty Information Limited Lifetime Warranty Warranty Exclusions Warranty Conditions and ExclusionsOther Rights HOW to Claim This warranty is void ifMelbourne Perth Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit Clear Space Lighting Instructions IPI Final inspection by Nine Hour Safety Shutdown Feature Control Module Operation Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Qualified Service Technician Gasket Seal and Glass Assembly InspectionLogs Firebox Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a fire hazard Framing and Clearances Selecting Appliance Location Clearances Constructing the Appliance ChaseClearance to heat shield Minimum Framing Dimensions Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances MIN. Clearance in. mm Clearance Vent Information and Diagrams USE SLP Series Components only Top Vent Horizontal TerminationV1 Minimum H1 Maximum Top Vent Horizontal Termination Two Elbows Minimum + H 2 Maximum Top Vent Horizontal Termination Three Elbows Min Max Straight Up Vertical Flue System Top Vent Vertical TerminationMAX. RUN Model Flue System Approvals And InstallationsFlue Termination Approvals Top Vent Vertical Termination Two Elbows H1 Maximum V1 + V2 Min Top Vent Vertical Termination Three Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Rear Vent Horizontal Termination No Elbow One 45º ElbowUSE DVP Series Components only H1 Minimum H1 Maximum Rear Vent Horizontal Termination Two Elbows H3H2 Minimum Maximum Rear Vent Vertical Termination One Elbow Two ElbowsV1 Minimum H1 + H2 Maximum Maximum Minimum + H 2 Maximum Rear Vent Vertical Termination Three ElbowsMinimum + H 2 + H Maximum Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Install Attic Insulation Shield Installing the Optional Heat-Zone-240V KitFlat Ceiling Installation Vaulted Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Installing the Non-combustible Board Securing and Leveling the Appliance Components Removal For Service Parts ReplacementAdjustments And Replacement Parts Install Trim and/or Surround Installing Vent Pipe DVP and SLP Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Support Brackets Install Firestops For Horizontal Terminations using the SLP-TRAP2 or DVP-TRAP2 Flue Termination Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Assemble and Install Storm Collar Install Vertical Termination Cap Gas Information Gas Connection GAS Access Wiring Requirements IntelliFire Plus Ignition System WiringOptional Accessories Requirements Optional Remote Control Receiver Location Blower Kit Contents Installation PrecautionsFireplace Specific Information Introduction Changing Temperature Scale Installation of Remote Control Housing AUX300CE Module Installation Fan InstallationProgramming the RC300AU to the Control Module Remote Position Learn Button Idle When Remote is in on Mode Standby modeDisplay Screen Function Buttons About on Mode About OFF ModeAdjusting Flame Height Adjusting Fan Speed Adjusting Thermostat Adjusting TimerSetting the Child Lock Power Outage Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Facing Material Finishing741 837 Appliance Setup Remove Fixed Glass AssemblyClean the Appliance Accessories Log Placement Instructions Log Assembly LOGS-350CE-D Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension DiagramLocation Inches Millimeters Maintenance Tasks Inspect Maintenance Tasks Vent Components Diagrams DVP-AS2 DVP-TRAP2 Mm Heat Shield 15-1/8 384 mmEffective Length Horizontal Termination Cap DVP-HRC-SS DVP-HRC-ZC-SS SLP45 SLP90SLP-PIPE SLP-WS SLP-TVHW Vertical Termination CapDVP-FBHT SLP90 SL-2DVP DVP-FBHT Log Set Assembly Description Comments Part Number Service Parts Beginning Manufacturing Date July Ending Manufacturing Date Service Parts List Conversion Kits Contact Information