One 45º Elbow | Heat & Glo LifeStyle 350TRSILP-AUF, 350TRSI-AUF

Rear Vent - Horizontal Termination

No Elbow

USE DVP SERIES COMPONENTS ONLY

H

H1 Minimum	H1 Maximum
6-1/2 in. (165 mm)	18 in. (457 mm)

Figure 7.12

One 45º Elbow

Do not use a 45º elbow in corner installations. Use two 90º elbows instead.

H1

USE DVP SERIES COMPONENTS ONLY

Figure 7.13

34	Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12

Image 34

Heat & Glo LifeStyle 350TRSILP-AUF Rear Vent Horizontal Termination No Elbow, One 45º Elbow, H1 Minimum H1 Maximum

Contents

Do Discardnot Models 350TRSI-AUF 350TRSILP-AUFWhat to do if you smell gas Hot glass will cause burns Models 350TRSI-AUF, 350TRSILP-AUF Congratulations Homeowner Reference Information Sans Compliance Novida Testing ServiceSans Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials Australian Warranty Information Limited Lifetime Warranty Warranty Exclusions Warranty Conditions and ExclusionsOther Rights HOW to Claim This warranty is void ifMelbourne Perth Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fan Kit Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Lighting Instructions IPI Final inspection by Nine Hour Safety Shutdown Feature Control Module Operation Frequently Asked Questions After Fireplace is Lit Maintenance and Service Logs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a fire hazard Framing and Clearances Selecting Appliance Location Clearances Constructing the Appliance ChaseClearance to heat shield Minimum Framing Dimensions Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances MIN. Clearance in. mm Clearance Vent Information and Diagrams USE SLP Series Components only Top Vent Horizontal TerminationV1 Minimum H1 Maximum Top Vent Horizontal Termination Two Elbows Minimum + H 2 Maximum Top Vent Horizontal Termination Three Elbows Min Max Straight Up Vertical Flue System Top Vent Vertical TerminationMAX. RUN Model Flue System Approvals And InstallationsFlue Termination Approvals Top Vent Vertical Termination Two Elbows H1 Maximum V1 + V2 Min Top Vent Vertical Termination Three Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum USE DVP Series Components only Rear Vent Horizontal Termination No ElbowOne 45º Elbow H1 Minimum H1 Maximum Rear Vent Horizontal Termination Two Elbows H3H2 Minimum Maximum Rear Vent Vertical Termination One Elbow Two ElbowsV1 Minimum H1 + H2 Maximum Maximum Minimum + H 2 Maximum Rear Vent Vertical Termination Three ElbowsMinimum + H 2 + H Maximum Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Flat Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-Zone-240V Kit Vaulted Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Installing the Non-combustible Board Securing and Leveling the Appliance Adjustments And Replacement Parts Components Removal For ServiceParts Replacement Install Trim and/or Surround Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Support Brackets Install Firestops For Horizontal Terminations using the SLP-TRAP2 or DVP-TRAP2 Flue Termination Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Assemble and Install Storm Collar Install Vertical Termination Cap Gas Information Gas Connection GAS Access Optional Accessories Requirements Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Remote Control Receiver Location Blower Fireplace Specific Information Kit ContentsInstallation Precautions Introduction Changing Temperature Scale Installation of Remote Control Housing Programming the RC300AU to the Control Module AUX300CE Module InstallationFan Installation Remote Position Learn Button Display Screen Idle When Remote is in on ModeStandby mode Function Buttons Adjusting Flame Height About on ModeAbout OFF Mode Adjusting Fan Speed Setting the Child Lock Adjusting ThermostatAdjusting Timer Power Outage Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Facing Material Finishing741 837 Clean the Appliance Appliance SetupRemove Fixed Glass Assembly Accessories Log Placement Instructions Log Assembly LOGS-350CE-D Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension DiagramLocation Inches Millimeters Maintenance Tasks Inspect Maintenance Tasks Vent Components Diagrams DVP-AS2 Effective Length DVP-TRAP2Mm Heat Shield 15-1/8 384 mm Horizontal Termination Cap DVP-HRC-SS DVP-HRC-ZC-SS SLP-PIPE SLP45SLP90 SLP-WS DVP-FBHT SLP90 SL-2DVP SLP-TVHWVertical Termination Cap DVP-FBHT Log Set Assembly Description Comments Part Number Service Parts Beginning Manufacturing Date July Ending Manufacturing Date Service Parts List Conversion Kits Contact Information