Heat & Glo LifeStyle 350TRSI-AUF, 350TRSILP-AUF specification

LOG #6 (SRV540-704):Place log #6 against the second and third grate tines.

If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12

Image 67

Contents

Hot glass will cause burns Models 350TRSI-AUF 350TRSILP-AUFWhat to do if you smell gas Do Discardnot Models 350TRSI-AUF, 350TRSILP-AUF Homeowner Reference Information Congratulations Sans Compliance Novida Testing ServiceSans User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Finishing Limited Lifetime Warranty Australian Warranty Information Warranty Exclusions Warranty Conditions and ExclusionsOther Rights HOW to Claim This warranty is void ifMelbourne Perth Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit Final inspection by Lighting Instructions IPI Control Module Operation Nine Hour Safety Shutdown Feature After Fireplace is Lit Frequently Asked Questions Maintenance and Service Firebox Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Logs Typical Appliance System Getting Started Any such action may cause a fire hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and Components Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance ChaseClearance to heat shield Minimum Framing Dimensions Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Vent Termination Minimum Clearances Termination Locations Clearance MIN. Clearance in. mm Vent Information and Diagrams USE SLP Series Components only Top Vent Horizontal TerminationV1 Minimum H1 Maximum Minimum + H 2 Maximum Top Vent Horizontal Termination Two Elbows Min Max Top Vent Horizontal Termination Three Elbows Straight Up Vertical Flue System Top Vent Vertical TerminationMAX. RUN Model Flue System Approvals And InstallationsFlue Termination Approvals H1 Maximum V1 + V2 Min Top Vent Vertical Termination Two Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three Elbows H1 Minimum H1 Maximum Rear Vent Horizontal Termination No ElbowOne 45º Elbow USE DVP Series Components only H3H2 Rear Vent Horizontal Termination Two Elbows Minimum Maximum Rear Vent Vertical Termination One Elbow Two ElbowsV1 Minimum H1 + H2 Maximum Maximum Minimum + H 2 Maximum Rear Vent Vertical Termination Three ElbowsMinimum + H 2 + H Maximum Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe DVP SLP Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-Zone-240V Kit Flat Ceiling Installation Top Vent Appliance Preparation Cut the metal retaining band and fold the sides out Rear Vent Securing and Leveling the Appliance Installing the Non-combustible Board Install Trim and/or Surround Components Removal For ServiceParts Replacement Adjustments And Replacement Parts Assemble Pipe Sections Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Vent Sections DVP Pipe Only Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Firestops Install Support Brackets Flue Termination For Horizontal Terminations using the SLP-TRAP2 or DVP-TRAP2 Heat Shield Requirements for Horizontal Termination Install Metal Roof Flashing Install Vertical Termination Cap Assemble and Install Storm Collar Gas Connection Gas Information GAS Access Optional Remote Control Receiver Location Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Accessories Requirements Blower Introduction Kit ContentsInstallation Precautions Fireplace Specific Information Installation of Remote Control Housing Changing Temperature Scale Remote Position Learn Button AUX300CE Module InstallationFan Installation Programming the RC300AU to the Control Module Function Buttons Idle When Remote is in on ModeStandby mode Display Screen Adjusting Fan Speed About on ModeAbout OFF Mode Adjusting Flame Height Power Outage Adjusting ThermostatAdjusting Timer Setting the Child Lock Symptom Possible Cause Corrective Action Frequently Asked Questions/Troubleshooting Facing Material Finishing741 837 Accessories Appliance SetupRemove Fixed Glass Assembly Clean the Appliance Log Assembly LOGS-350CE-D Log Placement Instructions Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension DiagramLocation Inches Millimeters Inspect Maintenance Tasks Maintenance Tasks DVP-AS2 Vent Components Diagrams Horizontal Termination Cap DVP-TRAP2Mm Heat Shield 15-1/8 384 mm Effective Length DVP-HRC-SS DVP-HRC-ZC-SS SLP-WS SLP45SLP90 SLP-PIPE DVP-FBHT SLP-TVHWVertical Termination Cap DVP-FBHT SLP90 SL-2DVP Description Comments Part Number Log Set Assembly Beginning Manufacturing Date July Ending Manufacturing Date Service Parts Conversion Kits Service Parts List Contact Information

Heat & Glo LifeStyle owner manual Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12

Models: 350TRSI-AUF 350TRSILP-AUF

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12