SLP45, SLP90, Slp-Pipe, Slp-Ws | Heat & Glo LifeStyle 350TRSI-AUF

B. Vent Components Diagrams (continued)

6-1/2 in.

6-1/2 in.

165 mm

165 mm

6-1/2 in.

165 mm

8-3/4 in.

9-1/4 in.

222 mm

6 in.

235 mm

152 mm

6-5/8 in.

168 mm

6-5/8 in.

SLP45

168 mm

45° Elbow

9-7/8 in.

251 mm

SLP90

90° Elbow

Effective Height/Length

Pipe

inches

mm

Effective

SLP4

4

102

Height/

SLP6

6

152

Length

SLP12

12

305

SLP24

24

610

SLP36

36

914

SLP48

48

1219

SLP-PIPE

SLP6A

2 - 6

51 - 152

SLP-WS

SLP12A

2 - 12

51 - 305

Wall Shield Firestop

SLP-HVS	SLP-FS
Horizontal Pipe	Ceiling Firestop
Support

Figure 16.6 SLP Series Vent Components

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12

75

Image 75

Heat & Glo LifeStyle 350TRSI-AUF, 350TRSILP-AUF owner manual SLP45, SLP90, Slp-Pipe, Slp-Ws, Slp-Hvs Slp-Fs

Contents

Hot glass will cause burns Models 350TRSI-AUF 350TRSILP-AUFWhat to do if you smell gas Do Discardnot Models 350TRSI-AUF, 350TRSILP-AUF Homeowner Reference Information Congratulations Novida Testing Service Sans ComplianceSans User Guide Table of Contents Reference Materials Appliance SetupTroubleshooting Finishing Limited Lifetime Warranty Australian Warranty Information Warranty Conditions and Exclusions Warranty ExclusionsOther Rights This warranty is void if HOW to ClaimMelbourne Perth Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit Final inspection by Lighting Instructions IPI Control Module Operation Nine Hour Safety Shutdown Feature After Fireplace is Lit Frequently Asked Questions Maintenance and Service Firebox Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Logs Typical Appliance System Getting Started Any such action may cause a fire hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and Components Selecting Appliance Location Framing and Clearances Constructing the Appliance Chase ClearancesClearance to heat shield Minimum Framing Dimensions Mantel and Wall Projections Combustible MantelsCombustible Mantel Legs or Wall Projections Vent Termination Minimum Clearances Termination Locations Clearance MIN. Clearance in. mm Vent Information and Diagrams Top Vent Horizontal Termination USE SLP Series Components onlyV1 Minimum H1 Maximum Minimum + H 2 Maximum Top Vent Horizontal Termination Two Elbows Min Max Top Vent Horizontal Termination Three Elbows Top Vent Vertical Termination Straight Up Vertical Flue SystemMAX. RUN Flue System Approvals And Installations ModelFlue Termination Approvals H1 Maximum V1 + V2 Min Top Vent Vertical Termination Two Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three Elbows H1 Minimum H1 Maximum Rear Vent Horizontal Termination No ElbowOne 45º Elbow USE DVP Series Components only H3H2 Rear Vent Horizontal Termination Two Elbows Rear Vent Vertical Termination One Elbow Two Elbows Minimum MaximumV1 Minimum H1 + H2 Maximum Rear Vent Vertical Termination Three Elbows Maximum Minimum + H 2 MaximumMinimum + H 2 + H Maximum Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Pipe DVP SLP Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-Zone-240V Kit Flat Ceiling Installation Top Vent Appliance Preparation Cut the metal retaining band and fold the sides out Rear Vent Securing and Leveling the Appliance Installing the Non-combustible Board Install Trim and/or Surround Components Removal For ServiceParts Replacement Adjustments And Replacement Parts Assemble Pipe Sections Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Vent Sections DVP Pipe Only Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Firestops Install Support Brackets Flue Termination For Horizontal Terminations using the SLP-TRAP2 or DVP-TRAP2 Heat Shield Requirements for Horizontal Termination Install Metal Roof Flashing Install Vertical Termination Cap Assemble and Install Storm Collar Gas Connection Gas Information GAS Access Optional Remote Control Receiver Location Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Accessories Requirements Blower Introduction Kit ContentsInstallation Precautions Fireplace Specific Information Installation of Remote Control Housing Changing Temperature Scale Remote Position Learn Button AUX300CE Module InstallationFan Installation Programming the RC300AU to the Control Module Function Buttons Idle When Remote is in on ModeStandby mode Display Screen Adjusting Fan Speed About on ModeAbout OFF Mode Adjusting Flame Height Power Outage Adjusting ThermostatAdjusting Timer Setting the Child Lock Symptom Possible Cause Corrective Action Frequently Asked Questions/Troubleshooting Finishing Facing Material741 837 Accessories Appliance SetupRemove Fixed Glass Assembly Clean the Appliance Log Assembly LOGS-350CE-D Log Placement Instructions Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Troubleshooting Appliance Dimension Diagram Reference MaterialsLocation Inches Millimeters Inspect Maintenance Tasks Maintenance Tasks DVP-AS2 Vent Components Diagrams Horizontal Termination Cap DVP-TRAP2Mm Heat Shield 15-1/8 384 mm Effective Length DVP-HRC-SS DVP-HRC-ZC-SS SLP-WS SLP45SLP90 SLP-PIPE DVP-FBHT SLP-TVHWVertical Termination Cap DVP-FBHT SLP90 SL-2DVP Description Comments Part Number Log Set Assembly Beginning Manufacturing Date July Ending Manufacturing Date Service Parts Conversion Kits Service Parts List Contact Information