Contact Information | Heat & Glo LifeStyle 350TRSILP-AUF manual

E. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc.

7571 215th Street West, Lakeville, MN 55044

www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating	• Read, understand and follow
and maintenance	these instructions for safe
instructions included.	installation and operation.

•Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487, 5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.

2000-945

Printed in U.S.A. - Copyright 2012

80	Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. o • 6/12

Image 80

Heat & Glo LifeStyle 350TRSILP-AUF, 350TRSI-AUF owner manual Contact Information

Contents

Models 350TRSI-AUF 350TRSILP-AUF What to do if you smell gasDo Discardnot Hot glass will cause burns Models 350TRSI-AUF, 350TRSILP-AUF Congratulations Homeowner Reference Information Sans Novida Testing ServiceSans Compliance Table of Contents User Guide Appliance Setup TroubleshootingFinishing Reference Materials Australian Warranty Information Limited Lifetime Warranty Other Rights Warranty Conditions and ExclusionsWarranty Exclusions Melbourne Perth This warranty is void ifHOW to Claim Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit Clear Space Lighting Instructions IPI Final inspection by Nine Hour Safety Shutdown Feature Control Module Operation Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Qualified Service Technician Gasket Seal and Glass Assembly InspectionLogs Firebox Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a fire hazard Framing and Clearances Selecting Appliance Location Clearance to heat shield Constructing the Appliance ChaseClearances Minimum Framing Dimensions Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Termination Locations Vent Termination Minimum Clearances MIN. Clearance in. mm Clearance Vent Information and Diagrams V1 Minimum H1 Maximum Top Vent Horizontal TerminationUSE SLP Series Components only Top Vent Horizontal Termination Two Elbows Minimum + H 2 Maximum Top Vent Horizontal Termination Three Elbows Min Max MAX. RUN Top Vent Vertical TerminationStraight Up Vertical Flue System Flue Termination Approvals Flue System Approvals And InstallationsModel Top Vent Vertical Termination Two Elbows H1 Maximum V1 + V2 Min Top Vent Vertical Termination Three Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Rear Vent Horizontal Termination No Elbow One 45º ElbowUSE DVP Series Components only H1 Minimum H1 Maximum Rear Vent Horizontal Termination Two Elbows H3H2 V1 Minimum H1 + H2 Maximum Rear Vent Vertical Termination One Elbow Two ElbowsMinimum Maximum Minimum + H 2 + H Maximum Rear Vent Vertical Termination Three ElbowsMaximum Minimum + H 2 Maximum Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Install Attic Insulation Shield Installing the Optional Heat-Zone-240V KitFlat Ceiling Installation Vaulted Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Installing the Non-combustible Board Securing and Leveling the Appliance Components Removal For Service Parts ReplacementAdjustments And Replacement Parts Install Trim and/or Surround Installing Vent Pipe DVP and SLP Pipe Attach Vent to the Firebox AssemblyAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Support Brackets Install Firestops For Horizontal Terminations using the SLP-TRAP2 or DVP-TRAP2 Flue Termination Install Metal Roof Flashing Heat Shield Requirements for Horizontal Termination Assemble and Install Storm Collar Install Vertical Termination Cap Gas Information Gas Connection GAS Access Wiring Requirements IntelliFire Plus Ignition System WiringOptional Accessories Requirements Optional Remote Control Receiver Location Blower Kit Contents Installation PrecautionsFireplace Specific Information Introduction Changing Temperature Scale Installation of Remote Control Housing AUX300CE Module Installation Fan InstallationProgramming the RC300AU to the Control Module Remote Position Learn Button Idle When Remote is in on Mode Standby modeDisplay Screen Function Buttons About on Mode About OFF ModeAdjusting Flame Height Adjusting Fan Speed Adjusting Thermostat Adjusting TimerSetting the Child Lock Power Outage Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action 741 837 FinishingFacing Material Appliance Setup Remove Fixed Glass AssemblyClean the Appliance Accessories Log Placement Instructions Log Assembly LOGS-350CE-D Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 Heat & Glo 350TRSI-AUF, 350TRSILP-AUF 2089-980 Rev. o 6/12 IntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Location Inches Millimeters Appliance Dimension DiagramReference Materials Maintenance Tasks Inspect Maintenance Tasks Vent Components Diagrams DVP-AS2 DVP-TRAP2 Mm Heat Shield 15-1/8 384 mmEffective Length Horizontal Termination Cap DVP-HRC-SS DVP-HRC-ZC-SS SLP45 SLP90SLP-PIPE SLP-WS SLP-TVHW Vertical Termination CapDVP-FBHT SLP90 SL-2DVP DVP-FBHT Log Set Assembly Description Comments Part Number Service Parts Beginning Manufacturing Date July Ending Manufacturing Date Service Parts List Conversion Kits Contact Information