Signal definitions, 1 TX+ / TX | Hitachi HTS543280L9A300 manual

5K320 SATA OEM Specification

7.3Signal definitions

The pin assignments of interface signals are listed as follows:

	No.		Plug Connector pin definition	Signal	I/O

	S1	GND	2nd mate	Gnd
	S2	A+	Differential signal A from Phy	RX+	Input

	S3	A-		RX-	Input
Signal
Signal	S4	Gnd	2nd mate	Gnd
	S5	B-	Differential signal B from Phy	TX-	Output

	S6	B+		TX+	Output

	S7	Gnd	2nd mate	Gnd
			Key and spacing separate signal and power
			segments
	P1	V33	3.3V power	3.3V

	P2	V33	3.3V power	3.3V

	P3	V33	3.3V power, pre-charge, 2nd Mate	3.3V

	P4	Gnd	1st mate	Gnd
	P5	Gnd	2nd mate	Gnd

	P6	Gnd	2nd mate	Gnd

	P7	V5	5V power,pre-charge,2nd Mate	5V

	P8	V5	5V power	5V
Power
Power	P9	V5	5V power	5V
	P10	Gnd	2nd mate	Gnd

	P11	DAS/DSS	Device Activity Signal / Disable Staggered	Note 1
			Spinup 1
	P12	Gnd	1st mate	Gnd

	P13	V12	12V power,pre-chage,2nd mate	V12

	P14	V12	12V power	V12

	P15	V12	12V power	V12

Table 23. Interface connector pins and I/O signals

Note 1;

Pin P11 is used by the drive to provide the host with an activity indication and by the host to indicate whether staggered spinup should be used.

The signal the drive provides for activity indication is a low-voltage low-current driver.

If pin P11 is asserted low the drive shall disable staggered spin-up and immediately initiate

spin-up. If pin P11 is not connected in the host (floating), the drive shall enable staggered spin-up.

7.3.1TX+ / TX-

These signal are the outbound high-speed differential signals that are connected to the serial ATA cable

7.3.2RX+ / RX-

These signals are the inbound high-speed differential signals that are connected to the serial ATA cable.

The following standard shall be referenced about signal specifications.

Serial ATA: High Speed Serialized AT Attachment Revision 1.0a 7-January -2003

40

Image 40

Hitachi HTS543280L9A300 manual Signal definitions, 1 TX+ / TX, 2 RX+ / RX, Interface connector pins and I/O signals

Contents

Hitachi Travelstar 5K320 Copyright Hitachi Global Storage Technologies Table of Contents 11.6 List of Figures List of Tables 5K320 Sata OEM Specification 5K320 Sata OEM Specification 5K320 Sata OEM Specification General Introduction Abbreviations EEC PIO References Drive handling precautionsGeneral caution Outline of the drive Part 1 Functional Specification Fixed disk subsystem description Head disk assembly dataControl Electronics Formatted capacity by model number Fixed disk characteristicsFormatted capacity by model number Data sheet Data sheetCylinder allocation Cylinder allocation Command overhead Performance characteristicsPerformance characteristics Mechanical positioning Average seek time including settlingFull stroke seek Average latency Drive ready time Drive ready time Mode transition time Operating mode at power onAdaptive power save control Operating mode Data loss on power off Write safetyData integrity Write Cache Data buffer test Error recoveryAutomatic reallocation ECC Specification Temperature and humidityEnvironment Corrosion test Conductive noise Radiation noiseMagnetic flux density limits DC power requirements Requirements Power consumption efficiency Power consumption efficiency Service life and usage condition ReliabilityData reliability Failure prediction S.M.A.R.T Preventive maintenance Required Power-Off SequencePower switch design considerations Load/unload Test considerations Mechanical specifications Physical dimensions and weightPhysical dimensions and weight Mounting hole locations Mounting orientation Connector descriptionLoad/unload mechanism Vibration and shock Operating vibrationRandom vibration Swept sine vibration Operating shock Nonoperating vibrationNonoperating shock Sound power level Weighted sound powerAcoustics Discrete tone penalty Identification labels Electromagnetic compatibility Packaging SafetySubstance restriction requirements Interface connector Electrical interface specificationsCabling Signal definitions Interface connector pins and I/O signals1 TX+ / TX 2 RX+ / RX 5K320 Sata OEM Specification Out of band signaling M R E S E T / C O M in IT M W a K E 5K320 Sata OEM Specification Part 2 Interface Specification General IntroductionTerminology Interrupt request Device or Host Physical Interface Deviations from StandardRegisters Command register Register naming conventionDevice Control Register Register naming convention and correspondence Error Register Features RegisterError Register Device Register LBA High Register LBA Low RegisterLBA Mid Register Sector Count Register Corr COR Reset Response Reset Response TableGeneral Operation Descriptions Register Initialization Diagnostic and Reset considerations Default Register ValuesDiagnostic Codes Reset error register values Power-off considerations Required power-off sequenceDevice’s behavior by ATA commands Emergency unload Sector Addressing Mode Power Management FeatureLogical CHS Addressing Mode LBA Addressing Mode Power Mode Power Management CommandsStandby/Sleep command completion timing Interface Capability for Power Modes Initial Power Mode at Power On Performance Idle modeActive Idle mode Low Power Idle mode Interface Power Management Mode Slumber and Partial 12.8 S.M.A.R.T. FunctionTransition Time Attributes Security Mode Feature Set Password Master Password Revision CodeSecurity Level Operation example Operation from POR after User Password is set Initial Setting User Password Lost Usual Operation Command Table Attempt limit for Security Unlock command Command table for device lock operation Protected Area Function Able 36 Command table for device lock operationRead Native Max Address ‘F8’h Set Max Address ‘F9’h Example for operation In LBA mode Shipping HDDs from HDD manufacturer Set Max security extension commands Set Max Set Password data content Write Cache Function Seek OverlapReassign Function 12.14 48-bit Address Feature Set Non recovered write errorsNon recovered read errors Recovered read errors Software Setting Preservation Feature Set Preserved software settings Smart Command Transport SCT Native Command QueuingPreserved Software Setting SCT Action Code Supported Data In Commands Command ProtocolData Out Commands Non-Data Commands DMA Data Transfer Commands First-parity DMA Commands Command Descriptions Command set + Vendor specific command Command Set Subcommand Output Registers Input Registers Check Power Mode Command E5h/98h Check Power Mode E5h/98hInput Parameters From The Device Device Configuration Overlay B1h Device Configuration Restore subcommand C0hDevice Configuration Freeze Lock subcommand C1h Device Configuration Overlay Command B1h Device Configuration Identify subcommand C2h Device Configuration SET subcommand C3h Device Configuration Overlay Data structure DCO error information definition Download Command 92h Download Microcode 92h 5K320 Sata OEM Specification Execute Device Diagnostic 90h Execute Device Diagnostic Command 90h Flush Cache Command E7h Flush Cache E7h Flush Cache EXT Command EAh Flush Cache Ext EAh Format Track 50h Vendor Specific Format Track Command 50hOutput Parameters To The Device LBA Low Format Unit Command F7h Format Unit F7h Vendor Specific Identify Device Command ECh Identify Device ECh Identify device information Identify device information 5K320 Sata OEM Specification Identify device information Identify device information Identify device information Identify device information 7AB8H =ATA8-AST 101 102 Idle E3h/97h Idle Command E3h/97hOutput Parameters To The Device Idle Immediate Command E1h/95h Unload FeatureIdle Immediate E1h/95h Initialize Device Parameters Command 91h Initialize Device Parameters 91h Read Buffer Command E4h Read Buffer E4h Read DMAC8h/C9h Read DMA Command C8h/C9hOutput Parameters To The Device Sector Count Read DMA Ext Command 25h Read DMA Ext 25h Read Fpdma Queued Command 60h Output Parameters To The Device Feature CurrentFeature Previous Read Fpdma Queued 60h Read Log Ext Command 2Fh CommandRead Log Ext2Fh Log address definition Extended comprehensive Smart error log General purpose Log Directory Error Log version Error log indexExtended Error log data structure Extended comprehensive Smart error Log Command data structure Error data structure Device error count Extended Self -test log sectorSelf-test log data structure revision number Extended Self-test log data structure Command Error Command Error informationSelf-test descriptor index Extended Self-test log descriptor entry Counter Reset Mechanisms Phy Event CounterCounter Identifiers Read Log Ext Log Page 11h Phy Event Counter information Read Multiple C4h Read Multiple Command C4hInput Paramete rs From The Device Read Multiple Ext Command 29h Read Multiple Ext 29h Read Native Max Address Command F8h Read Native Max Address F8h Read Native Max Address Ext Command 29h Read Native Max Address Ext 27h Read Sectors Command 20h/21h Read Sectors 20h/21h Read Sectors Ext Command 24h Read Sectors Ext 24h Read Verify Sectors Command 40h/41h Read Verify Sectors 40h/41h Read Verify Sectors Ext Command 42h Read Verify Sectors Ext 42h Recalibrate Command 1xh Recalibrate 1xh Security Disable Password Command F6h Security Disable Password F6hPassword Information for Security Disable Password command Security Erase Prepare Command F3h Security Erase Prepare F3h Security Erase Unit Command F4h Security Erase Unit F4hErase Unit Information Identifier HTS543232L9SA00 / HTS5432 32L9A300 Security Freeze Lock Command F5h Security Freeze Lock F5h Security Set Password Command F1h Security Set Password F1hSecurity Set Password Information Password Security LevelRevision Code Identifier=User / Security level = High Security Unlock F2h Security Unlock Command F2hSecurity Unlock Information Seek Command 7xh Seek 7xh Sense Condition Command F0h Sense Condition F0h vendor specific Set Features EFh Set Features Command EFh Description Set Max a ddress Command F9h Set Max Address F9h 04h SET MAX Freeze Lock Set Max Address Ext 37h Set Max a ddress Ext Command 37hInput Parameters From The Device LBA Low HOB=0 142 Set Multiple Command C6h Set Multiple C6h Sleep Command E6h/99h Sleep E6h/99h M.A.R.T. Function Set Command B0h 14.40.1 S.M.A.R.T. Sub commands14.40 S.M.A.R.T Function Set B0h A.R.T. Read Attribute Thresholds Subcommand D1h A.R.T. Enable/Disable Attribute Autosave Subcommand D2hA.R.T. Save Attribute Values Subcommand D3h A.R.T. Execute Off-line Immediate Subcommand D4h Error StatusLBA Mid LBA High A.R.T. Read Log Sector Subcommand D5h A.R.T. Write Log Sector Subcommand D6hA.R.T. Enable Operations Subcommand D8h Log sector addresses A.R.T. Return Status Subcommand DAh A.R.T. Disable Operations Subcommand D9hA.R.T. Enable/Disable Automatic Off-Line Subcommand DBh Data Structure Revision Number Device Attributes Data StructureDevice Attribute Data Structure Individual Attribute Data Structure Individual Attribute Data StructureStatus Flag Definitions Off-Line Data Collection Status Self-test execution statusBit Automatic Off-Line Data Collection Status Value Definition Error Logging Capability Current Segment PointerOff-Line Data Collection Capability 14.40.2.8 S.M.A.R.T. Capability Device Attribute Thresholds Data Structure Self-test completion timeData Structure Checksum Individual Thresholds Data Structure 14.40.5 S.M.A.R.T. error log sector 14.40.4 S.M.A.R.T. Log DirectoryAttribute ID Numbers Attribute Threshold Error log pointer 14.40.5.1 S.M.A.R.T. error log versionError log data structure Value State X0h X1hX2h X3h Self-test log data structure Error Reporting M.A.R.T. Error CodesSelective self-test log data structure Selective self-test log data structure Standby E2h/96h Standby Immediate E0h/94h Write Buffer E8h Write DMA CAh/CBh Write DMA Ext 35h Write DMA FUA Ext 3Dh Write Fpdma Queued 61h Write Log Ext 3Fh Sector Count Previous Write Multiple C5h Write Multiple Ext 39h Write Multiple FUA Ext CEh Write Sectors 30h/31h Write Sectors Ext 34h Write Uncorrectable Ext 45h Number of continuous sectors to be marked low order, bits Comreset Timings Erase Unit F4h on Copyright Hitachi Global Storage Technologies