DO2Type | Honeywell W7761A specification

EXCEL 10 W7761A INPUT/OUTPUT DEVICE

Table C1. Input/Output Points (Right Continued).

Share (SH), Map (MA), Direct Access (DA)

E-Vision (EV): Calibrate (C), Monitor (M),

Parameter (P), Schematic (S)

Hardware Configuration (HW),

Manual Point (MN), Test (TS)

SH	MA	DA	EV	HW	MN	TS	Comments

		X		X			DO2Type:
							Refer to the description for DO1Type.

		X		X			DO3Type:
							Refer to the description for DO1Type.

		X		X			DO4Type:
							Refer to the description for DO1Type.

		X		X			DO5Type:
							Refer to the description for DO1Type.

		X		X			DO6Type:
							Refer to the description for DO1Type.

		X		X			DO7Type:
							Refer to the description for DO1Type.

		X		X			DO8Type:
							Refer to the description for DO1Type.

		X		X			FiftySixtyHz specifies the power supply frequency. Correctly selecting FiftySixtyHz
							decreases the noise picked up by analog sensor wiring from the power supply.
							When FiftySixtyHz is 1, the power supply frequency is Fifty Hz and when
							FiftySixtyHz is 0, the power supply frequency is Sixty Hz.

X	X	X	M				SrcCO2Level is an output network variable corresponding to the voltage or current
							input channel (AI5 or AI6) if the selection for a CO2 sensor was made via
							ncirioIoSelect.

X	X	X	M				SrcCurrentAI is an output network variable corresponding to the voltage or current
							input channel (AI5 or AI6) if the selection for a current sensor was made via
							ncirioIoSelect.

							SrcDigIn1Sts: There are four digital input channels (DI1 through DI4). If any of the
							four channels are configured, the corresponding output network variable will be
							updated with the value whose data type is SNVT_switch.

X	X	X	M				DI1State: There are four digital input channels (DI1 through DI4). If any of the four
							channels are configured, the corresponding output network variable will be updated
							with the value whose data type is SNVT_switch. Refer to the enumerated list that is
							shown in the Eng. Units/States column.

(continued)

52

74-2699

Image 52

Honeywell W7761A specifications DO2Type

Contents

Excel 10 W7761A Remote Input/Output Device List of Tables Appendices Description of Devices Typical system overview Control Application Control ProvidedProducts Covered Organization of Manual Product Names Agency Listings Abbreviations and Definitions Excel 10 W7761A INPUT/OUTPUT Device Construction Controllers Excel 10 W7761A Remote I/O Device W7761A construction in in. mm Performance Specifications Power List Of Available Points W7761A Specified Space Temperature Sensing Range Environmental Operating TemperatureShipping Temperature Memory Capacity Discharge Air Temperature Outdoor Air TemperatureReturn Air Temperature Mixed Air Temperature Wall Modules 5585 Configurations T7780 construction, subbase dimensions in in. mm Mixed-Output-Type Control Occupancy SensorWindow Open/Closed Digital Input Wall Module Options Plan The System OverviewApplication Steps Step No Description Determine Other Bus Devices Required Lay Out Communications and Power WiringBus Layout 750,1$ Power Wiring Power Budget Calculation Example VA Ratings For Transformer Sizing Device Description Line Loss VA Rating Nema class 2 transformer voltage output limits Line VOLTAGE` GREATER` Than 150 VAC General Considerations Prepare Wiring DiagramsW7761A Devices W7761A I/O Description Terminal Number Description Temperature Sensor DE V IC E Window Contact Contact Closed = Occupancy Sensor Occupied Valve Actuator Bus Termination Module Typical Pneumatic transducer Series 60 Floating to W7761A See for E-Bus termination wiring options +$672 Order Equipment Excel 10 W7750 ControllersT7770 Wall Modules Sensors Accessories Echelon Based Components and Parts Cabling Temperature Degrees Excel 10 Alarms Broadcasting the Service MessageW7761A Device Status LED T7780 Ddwm Bypass Pushbutton LED States Appendix A. Using E-Vision to Commission a W7761 Device Adding Analog Inputs Enthalpy 4 to 20 mA Adding Other VOLTAGE/CURRENT Sensors Adding Digital Inputs Appendix B. Sequences of Operation Room Temperature Sensor RmTempCommon Operations Window Sensor StatusWndw Dirty Filter MonitorSeries 60 Modulating Control Pulse Width Modulating PWM Control Temperature Relative Humidity RelativeAir Flow CO 2 Concentration Default Table C1. Input/Output Points Left Table C1. Input/Output Points Right Excel 10 W7761A INPUT/OUTPUT Device Values that can be assigned to any output channels English Metric or User Address DI3Sel1Type Refer to the description for DI1Sel1Type Stoff Stnul Stlow Stmed Sthigh Ston DO2Type Excel 10 W7761A INPUT/OUTPUT Device SrcDigIn2Sts Refer to the description for SrcDigIn1Sts Table C2. Control Parameters Left Table C2. Control Parameters Right SH MA DA EV HW MN TS Noalarm Table C3. Status Points Left Table C3. Status Points Right RIO1 Software version NvoStatus InOverride SH MA DA EV HW MN TS Table C4. Configuration Parameters Left Table C4. Configuration Parameters Right DO0 Higher than the value specified for AILowLimit DO4 Seconds = 25.6 seconds DO6PWMPeriod Refer to the description for DO1PWMPeriod Table C5. Direct Access And Special Points Left Table C5. Direct Access And Special Points Right Approximate Memory Size Estimating Procedure Fig. D-1. Point capacity estimate for Zone Manager Appendix E. Sensor Data for Calibration Resistance SensorsSensor Type Sensor Use 1956.79 Table E-4. Sensor Voltage Versus Humidity Voltage/Current SensorsHumidity Percentage Sensor Voltage C7600C1008 4 to 20 mA C7600C output current vs. humidity Sensor Type Fig. E-6. Graph of Sensor Current versus Enthalpy volts CO 2 Concentration PPM Sensor Voltage Table E-9. Sensor Voltage Versus CO 2 ConcentrationTable E-10. Sensor Voltage Versus Input Voltage To A/D Table E-11. Sensor Voltage Vdc Versus Pressure Inw Voltage to A/D Sensor VoltagePressure Inw kPa Sensor Voltage Vdc 3ODD