Honeywell W7761A T7780 DDWM Bypass Pushbutton

EXCEL 10 W7761A INPUT/OUTPUT DEVICE

38 74-2699

Table 10. LED States.

Alarm Condition Hardware or

Software Failure Service LED Blink Rate

(Cycles per second)

None None 1

Any alarm condition None 2

Don't Care Failed steady ON or OFF

1. Off—no power to the processor.

2. Continuously On—processor is in initialized state.

3. Slow Blink—controlling, normal state.

4. Fast Blink—when the Excel 10 has an alarm condition.

M10095

123456789101112131415J3

31302928272625242322212019181716

EARTH `

GR

OUNDL

EDBYPASSSENSORGR

OUNDSET PTA11

RGROUNDA12 RA13`

V/mA

GROUNDA14V/mA22

VDC

`

OUT

EBUS

D14GROUN

DD13D12GR

OUNDD1124 V

ACCOMOUT 1OUT 2OUT 3OUT 4 O

UT 5OU

T 6OUT 7OUT

8

STATUS`

LED

W7750

Fig. 25. LED location on W7761A.

T7780 DDWM Bypass Pushbutton

See Fig. 26 for the T7780 DDWM bypass pushbutton location (occupied or unoccupied). The T7780 DDWM has two methods

for generating its neuron ID, shorting two pads or winking.

1. Pressing the bypass pushbutton whenever a Carat (∇) on the bottom of the LCD display is flashing (Menu Selection

Mode).

2. Pressing the bypass pushbutton when the T7780A DDWM is in wink mode (LCD display shows WINK when E-Vision

sends a Service Message out on the E-Bus).

When the space covered by the T7780 DDWM is in Occupied mode, the sun symbol is shown on the left side of the LCD

display. When the space is in Standby mode, the half-sun symbol is shown. When the space is in Unoccupied mode, the moon

symbol is shown.

Contents

Main CONTENTS Excel 10 W7761A Remote Input/Output Device Page INTRODUCTION Description of Devices Fig. 1. Typical system overview. Control Application Control Provided Products Covered Organization of Manual Product Names not applicable to the RIO device EXCEL 10 W7761A INPUT/OUTPUT DEVICE Agency Listings Abbreviations and Definitions EXCEL 10 W7761A INPUT/OUTPUT DEVICE economizer dampers not Construction Controllers it is intended that the cover never be removed 9 74-2699 123456789101112131415J3 Fig. 3. Excel 10 W7761A Remote I/O Device. M10118 31302928272625242322212019181716 W7761A EXCEL 10 W7761A INPUT/OUTPUT DEVICE Fig. 4. W7761A construction in in. (mm). must Page Page CAUTION 80 T7770C Wall Modules T7770A1006 Configurations Mixed-Output-Type Control Occupancy Sensor Window Open/Closed Digital Input Wall Module Options Dirty Filter Monitor APPLICATION STEPS Overview Step 1. Plan The System Step 2. Determine Other Bus Devices Required Step 3. Lay Out Communications and Power Wiring E-Bus Layout Page Power Wiring IMPORTANT Page Page Make earth ground connections with the shortest possible wire run using 14 AWG (2.0 mm Step 4. Prepare Wiring Diagrams General Considerations W7761A Devices Page 26 74-2699 W7761A REMOTE I/O DEVICE Fig. 16. Typical T7770A and C7770A wiring diagram. (For note 2, refer to Fig. 15.) + - T7770A WALL MODULE C7770A AIR TEMPERATURE SENSOR W7761A REMO TE I/O DEVICE + - Enthalpy (4 to 20mA) Humidity (4 to 20mA) W7761A REMOTE I/O DEVICE + - Fig. 18. Typical Window and Occupancy sensor wiring diagram. (For note 2, refer to Fig. 15.) W7761A REMOTE I/O DEVICE + - PWM VALVE ACTUATOR W7761A REMOTE I/O DEVICE + - Fig. 20. Typical Pneumatic transducer (Series 60 - Floating) to W7761A. E-Bus Termination Module Page Page Step 5. Order Equipment Page Page Step 6. Configure Devices Step 7. Troubleshooting Troubleshooting Excel 10 Controllers and Wall Modules Temperature Sensor and Setpoint Potentiometer Resistance Ranges Alarms Broadcasting the Service Message W7761A Device Status LED T7780 DDWM Bypass Pushbutton APPENDICES Appendix A. Using E-Vision to Commission a W7761 Device. SENSOR CALIBRATION voltage/current is not supported on the W7761A. Page Page Appendix B. Sequences of Operation. Common Operations Page Appendix C. Complete List of Excel 10 W7761A Remote I/O Device User Addresses. writes if applicable as allowed Table C1. Input/Output Points (Left). Table C1. Input/Output Points (Right). Page Page Page Page Page Page ) Page Table C2. Control Parameters (Left). Table C2. Control Parameters (Right). Table C3. Status Points (Left). Table C3. Status Points (Right). Table C3. Status Points (Left Continued). Table C3. Status Points (Right Continued). EXCEL 10 W7761A INPUT/OUTPUT DEVICE Table C3. Status Points (Left Continued). Table C3. Status Points (Right Continued). Table C4. Configuration Parameters (Left). Table C4. Configuration Parameters (Right). Page Page Page Page Page Table C5. Direct Access And Special Points (Left). Table C5. Direct Access And Special Points (Right). Appendix D. Q7750A Excel 10 Zone Manager Point Estimating Guide. Approximate Memory Size Estimating Procedure. Direct Access Appendix E. Sensor Data for Calibration. Resistance Sensors. Page Voltage/Current Sensors. Page Page EXCEL 10 W7761A INPUT/OUTPUT DEVICE Fig. E-8. C7400A Solid State Enthalpy Sensor output current vs. relative humidity. DCBA (4) (10) (16) (21) (27) (32) (38) 605040 70 80 90 100