Manuals / Initio / Computer Equipment / Network Card

Initio INI-9100UW user manual Microsoft Windows 95 Driver Installation, Overview

Models: INI-9100UW INI-9100U

1 116

Download 116 pages 29.09 Kb

Page 53

Microsoft Windows 95 Driver Installation

Overview

The Initio INI-9100U/9100UW will support Microsoft Windows 95 with the addition of a software driver. The installation procedure described here requires some experience in Windows 95 system setup and administration. The device driver is transferred from the INITIO INI-9100U/9100UW DRIVER DISK 1 to the hard drive where it is automatically initialized during the system boot routine.

The following files are used for installation and will be found on the Initio INI- 9100U/9100UW DRIVER DISK 1:

INI910U.MPD	INI-9100U/9100UW SCSI Host Adapter Windows 95
	miniport driver.
INI910U.INF	Windows 95 installation information file.

Installation

The INI-9100U/9100UW driver developed for Windows 95 is loaded during the system boot routine and will remain resident on the drive. This is accomplished by following one of the three installation procedures listed:

∙New Windows 95 installation.

∙Adding the Initio Windows 95 device driver to an existing Windows 95 system.

∙Updating INI910U.MPD device driver

Reference Documentation:

∙Windows 95 installation and user’s guide

∙The systems setup and installation guide

∙The documentation for system peripherals

∙Initio documentation for the SCSI host adapter

The procedures described to make changes to the system have distinct differences. It is strongly suggested that the selected procedure be read and understood before proceeding with the system configuration changes. Please read the instructions carefully.

6-2

Image 53

Initio INI-9100UW user manual Microsoft Windows 95 Driver Installation, Overview

Contents

initio Initio Corporation 2188 Del Franco Street San Jose, CAU S E R ‘ S M A N U A L PCI ULTRA SCSI HIGH-PERFORMANCE BUS MASTER HOST ADAPTERTrademarks CopyrightChanges Technical SupportC\ type readme.txt more The README.TXT FileTHIS PAGE INTENTIONALLY LEFT BLANK HARDWARE INSTALLATION Table of ContentsHOST ADAPTER SETUP INTRODUCTIONMICROSOFT WINDOWS-NT MICROSOFT WINDOWSNOVELL NETWARE IBM OS/211-1 SCO UNIXWAREAPPENDIX 12-1THIS PAGE INTENTIONALLY LEFT BLANK viiiInside this manual MS-DOS/Windows Convention Notational ConventionsDescription UPPERCASETHIS PAGE INTENTIONALLY LEFT BLANK 1-12Introduction ∙ The features built into the INI-9100U/9100UWThis Chapter Is About ∙ What information this manual provides ∙ A description of the INI-9100U/9100UW host adapterThe Initio INI-9100U/9100UW host adapter Introductionfigure 1-1 INI-9100U Host adapter figure 1-2 INI-9100UW Host adapter Application and peripheral supportProduct features Plug and Play installationPlug and Play 133 MBytes per second PCI burst mode Hard Drives to 8 Gigabytes per drive capacityCommand Queuing Onboard BIOSProgrammable SCSI Auto-TerminationWhere to get help Product specificationsOperating Temperature Storage TemperatureInitio Corporation BBS 408 THIS PAGE INTENTIONALLY LEFT BLANK Getting Started This Chapter Is About ∙ Information on quick installation∙ SCSI bus setup for internal and external peripherals SCSI bus preparation Getting StartedHost adapter and the SCSI bus figure 2-1 Examples of SCSI bus termination SCSI bus terminationSCSI Devices Configuration Installation basicsHost Adapter Termination HighUnpacking and inspection Quick installation overviewInstalling the INI-9100U/9100UW host adapter and cabling Cable termination Configuring the host adapterPage This Chapter Is About ∙ Installing the INI-9100U/9100UW Hardware InstallationPreparing your SCSI device Hardware InstallationIntroduction figure 3-1 INI-9100U Board Layout figure 3-2 INI-9100UW Board Layout1. Power down the host computer and all peripherals Installation in ten easy stepsINI-9100U INI-9100UW3. Inserting the host adapter 2. Use static electricity discharge precautionsfigure 3-3 Inserting the INI-9100U/9100UW into a PCI slot 4. Installation of internal SCSI cablesfigure 3-4 Connecting the 50-pin internal flat ribbon cable 5. Drive activity LED6. Multiple Initiators 8. Host computer configuration 7. Installation of external SCSI cables9. System startup 10. SmartSCSI Setup Utility3-10 Hard disk drive preparationLow-level format ∙ Description of SmartSCSI features Host Adapter SetupThis Chapter Is About ∙ How to start the SmartSCSI Setup Utility When to use the SmartSCSI Setup Utility Host Adapter SetupRunning the SmartSCSI Setup Utility Press Ctrl I for SmartSCSI Setup UtilityScan Bus Device SetupMain menu options Page Enable Wide Negotiation INI-9100UW ONLY. This option determines whether the host adapter initiates wide data transfer with the specified SCSI device. However, not all SCSI devices can handle wide data transfer properly and this may cause problems with your system. If problems arise from wide SCSI negotiation, disable this option. The normal setting for this option is enabled yes Host Adapter Setup BIOS Setup Disk Utilities ∙ Device Driver Command Line Options ∙ Installing the Initio ASPI Driver to an Existing MS- DOS SystemMS-DOS/Windows This Chapter Is AboutInstallation MS-DOS Driver InstallationInstalling the Initio ASPI driver to an existing MS-DOS system OverviewA ENTER 4. Type DOSSETUP ENTER Installing the Initio ASPI driver to an existing Windows 3.1x systemCTRL + ALT + DEL CONTINUEDriver config options Device driver command line optionsTHIS PAGE INTENTIONALLY LEFT BLANK ∙ Installing the Initio driver into an existing Windows 95 system ∙ Installing the Initio driver into a new Windows 95 systemMicrosoft Windows ∙ Updating Initio device driversOverview Microsoft Windows 95 Driver InstallationInstallation New Windows 95 installation DRIVER tab, then select “CHANGE DRIVER...” 5. Select INITIO INI-9100U/9100UW Host Adapter, select “OK”, then 3. Select INITIO INI-9100U/9100UW Host Adapter, select “OK”, then Adding the Initio Driver to an existing Windows 95 systemUpdating the Initio device driver Page Page This Chapter Is About ∙ Installing the Initio driver into a new Windows NT systemMicrosoft Windows-NT Overview Microsoft Windows-NT Driver InstallationInstallation New Windows-NT installation ∙ Select “S” to skip mass storage detection ∙ Press “ENTER” to continue setting up Windows NT∙ Select “S” to configure additional SCSI adapters ∙ Remove diskette in drive A and set it aside ENTER∙ Insert INITIO INI-9100U/9100UW DRIVER DISK 1 and press ∙ Select Initio INI-9100U/9100UW SCSI Host Adapter see figurefigure 7-4 Select Initio driver 2. Select the DRIVERS tab from within the SCSI ADAPTERS group 3. In the INSTALL DRIVER window, select “HAVE DISK...”∙ In the DRIVERS window, select “ADD…” ∙ Insert INITIO INI-9100U/9100UW DRIVER DISK 1 into drive A∙ Type A\WINNT, select “CONTINUE” ∙ Select Initio INI-9100U/9100UW SCSI Host Adapter 7-10 ∙ Installing the driver in an existing NetWare system ∙ Installing the Initio driver in A new NetWare system∙ Device driver command line options Novell NetWareOverview Novell NetWare Driver InstallationInstallation New NetWare 4.xx installatione.g., d\netware4.0\english\ ENTER ∙ Press the Ins key to insert a new device driver Press ENTER ∙ Type A\netware\v4xENTER figure 8-2 Specify Initio Driver PathENTER name you have selected. To continue with installation press∙ Type CD \ NWSERVER ENTER ∙ Type SERVER ENTER Adding the Initio driver to an existing NetWare system∙ Select ini910U.DSK, press ENTER ∙ Insert INITIO INI-9100U/9100UW DRIVER DISK 1 into drive ADevice driver command line options ENTERLoad Pathname ini910u Driver Config Option Driver Config OptionsLoad Pathname ini910u Driver Config Option THIS PAGE INTENTIONALLY LEFT BLANK 8-10IBM OS/2 ∙ Installing the Initio driver in a new OS/2 installation∙ Adding the Initio driver to an existing OS/2 system ∙ Device driver command line optionsOverview IBM OS/2 Driver InstallationInstallation New OS/2 installation figure 9-1 Edit CONFIG.SYS file Adding the Initio driver to an existing OS/2 system4. Select OS2 and select SET 5. Select DESTINATION DIRECTORY3. Select CHANGE source directory to read as the root directory 9. Select INITIO INI-9100U/9100UW Device Driver for OS/2 select “OK” INSTALLDriver Config Options Device driver command line optionsTHIS PAGE INTENTIONALLY LEFT BLANK ∙ Installing the Initio driver in a new SCO UNIX installation This Chapter Is About ∙ Setting interrupts∙ Changing to INI-9100U/9100UW as the bootable host adapter SCO UNIX10-2 SCO UNIX Driver InstallationInstallation Overview10-3 Updating interrupts and hardware settingsInstalling the Initio driver in a new SCO UNIX system figure 10-3 Insert Initio INI-9100U/9100UW Driver Disk 10-4figure 10-2 Linking a package in SCO UNIX 10-5 Adding the Initio driver to an existing SCO UNIX system∙ Type i91u ENTER cd /etc/conf/cf.d Changing to the INI-9100U/9100UW as the bootable host adapterlinkunix ∙ Type i91u ENTERnumber attach∙ . /linkunix ENTER 10-7THIS PAGE INTENTIONALLY LEFT BLANK 11-8∙ Using multiple host adapters in UnixWare ∙ Installing the Initio driver in a new UnixWare installationSCO UnixWare ∙ Adding the Initio driver to an existing UnixWare system11-2 SCO UnixWare Driver InstallationInstallation Updating interrupts and hardware settingsfigure 11-1UnixWare Installation Installing the Initio driver in a new UnixWare system11-3 figure 11-2 Install Host Bus Adapter Drivers 11-4figure 11-3 Install another HBA Diskette ∙ Select CONTINUE INSTALLATION ∙ Select CONTINUE INSTALLATION again11-5 ∙ cp /stand/unix /stand/unix.org , press ENTER Adding the Initio driver to an existing UnixWare system∙ pkgadd -d diskette1 , press ENTER ∙ cd /etc/conf/sdevice.d∙ /etc/conf/bin/idbuild -M i910u ENTER ∙ cd / ENTER Using multiple Host Adapters11-7 ∙ shutdown -g0 0 is Zero ENTER ∙ Y ENTERRemoving the Initio driver from a UnixWare system ∙ shutdown -g0 where 0 is Zero ENTER ∙ Y ENTER∙ /etc/conf/bin/idbiuld -B -K ENTER ∙ /cp /etc/conf/cf.d/unix /stand/unix ENTER ∙ cd/ ENTER∙ Warranty This Chapter Is About ∙ Troubleshooting ∙ DOS Space 1 GigabyteAppendix 12-112-2 A Troubleshooting∙ Consult the SCO UnixWare Installation Handbook ∙ Type go ENTER12-3 MS-DOS, OS/2 & Windows NT B DOS Space 1GBNetWare SCO UNIX12-5 Drives with Multiple Operating SystemsPage 13-1 GlossaryThis Chapter Is About ∙ Common terms and definitions Definitions of Terms 13-2RESET condition, or an unexpected disconnect occurs 13-3FCC Compliance Statement Product WarrantyClass B Equipment Information to User 13-413-5 Declaration of the Manufacturer/ImporterEN 55 9100UW2 Declaration of Conformance