Read Only Stall Flag Encoder Flag | Intelligent Motion Systems 17

MNEMONIC	FUNCTION	TYPE
ST	Read Only Stall Flag	Encoder Flag

DESCRIPTION

The ST flag will be set to 1 when a stall is detected. It will be cleared upon execution of another motion command.

USAGE

PR ST

BR <addr>, ST=1

CL <addr>, ST=1

EXAMPLE RESPONSE:
ST=0	‘motor not stalled
ST=1	‘motor stalled

RELATED COMMANDS: EE, SF, ST

MNEMONIC		FUNCTION	TYPE
TE		Trip Enable Flag	Setup Flag
DESCRIPTION
This flag will enable or disable specified trip functions.
TE=0	TI Disabled	TP Disabled
TE=1	TI Enabled	TP Disabled
TE=2	TI Disabled	TP Enabled
TE=3	TI Enabled	TP Enabled

USAGE		DEFAULT
TE= <1-4>		0 (Trips Disabled)

EXAMPLE:
TE=1 ‘Enable trip on input functions

RELATED COMMANDS: I1-I4, P, S1-S4, TI, TP

MNEMONIC		FUNCTION	TYPE
TI		Trip on Input	Variable

DESCRIPTION

Sets up an input event (trip) for the specified input. There are two parameters for the TI variable. The first specifies the address of the subroutine that should be executed when the input goes to true. The second specifies which input line to monitor.

USAGE

TI=<input>,<addr/label>

EXAMPLE:
TI=2,K1	‘execute subroutine labeled K1 when input 2 is active.

RELATED COMMANDS: I1-4, S1-4, TP

60

Image 62

Intelligent Motion Systems 17 manual Read Only Stall Flag Encoder Flag, Trip Enable Flag Setup Flag, Trip on Input Variable

Contents

Operating Instructions Intelligent Motion Systems, Inc All Rights Reserved Table of Contents List of Figures Part 1 General Information and Hardware Specifications Intentionally Left Blank A t u r e S u m m a r y Standard Rotary Motor Lmax T a r y M o t o r Specification sC t i o n O v e r v i e w Control Knob LMAX2 MDI1719 N e a r M o t o r Specification sMDI1715 E e d F o r c e C u r v e 4 5 V D C MDI17 Linear ActuatorE e d F o r c e C u r v e 2 4 V D C MDI17 Acme Screws N e r a l Specification sR i v e 1 7 M o t i o n C o n t r o l a C M E S c r e w C o m m e n d e d I M S P o w e r S u p p l i e s E r m a l Specification sW e r S u p p l y R e q u i r e m e n t s A t u r e S u m m a r y MDrive23 Motion Control Specifications MDI2218 MDI2222 MDI2231 MDI23 Linear Actuator Refer to .10 for screw pitch information R i v e 2 3 M o t i o n C o n t r o l a C M E S c r e w MDI23 Acme Screws IP404MDI23 Page Intentionally Left Blank N C o n f i g u r a t i o n a n d D e s c r i p t i o n s Connector P1Y o u t a n d I n t e r f a c e G u i d e l i n e s C o m m e n d e d W i r i n g T e r f a c i n g R S 4 8 5 C o m m u n i c a t i o n s Connector P2 10 Pin HeaderT e r f a c i n g P o w e r N g l e M D r i v e RS-485 Interface, Multiple MDrive Motion Control System T e r f a c i n g I n p u t s T e r f a c i n g t h e D i g i t a l I / OE s o f t h e D i g i t a l I / O Input Functions TTL Interface to Input Group Truth Table I/O Used as a Group T e r f a c i n g O u t p u t s T e r f a c i n g a S i n g l e O u t p u t E x a m p l e s T e r f a c i n g t h e a n a l o g I n p u t M p l e U s a g e S t e m R e q u i r e m e n t s Install i n g a n d U s i n g I M S Te r m i n a lInstallation I n g t h e I M S Te r m i n a l S o f t w a r e 13 IMS Terminal Upgrader Window S t r u c t i o n s R i v e M o t i o n C o n t r o l P r o g r a m m i n gE r a t i o n a l M o d e s R i a b l e s A g s Y w o r d s T h F u n c t i o n s T i o n C o m m a n d s Read IO1 Setup PR S1 Read IO2 Setup PR S2 C o m m a n d s Please Note Any program labeled SU will execute on power-up VAR CT Mnemonic Function Unit Range Syntax Example Baud I n s t r u c t i o n s , Va r i a b l e s a n d F l a g s Symbol Function T h e m a t i c a l F u n c t i o n s Retrieve All Parameters Variable Baud Rate Setup VariableAcceleration Motion Variable Branch Program Instruction Busy Flag Read Only Motion Flag Clear Program Program Instruction Set Counter 2 Encoder Counts Motion VariableCall Subroutine Program Instruction Deceleration Motion Variable Set Encoder Deadband Setup VariableD1-D5 Digital Input Filtering Variable End Program Execution Program Instruction Drive Enable Flag Setup FlagDevice Name Setup Variable Read-Only Error Flag Status Flag Encoder Enable Flag Setup FlagEcho Mode Flag Setup Flag Error Number Variable Status Variable Execute Program Program Instruction Hold Program Execution Program Instruction Home to Index Mark Variable Setup VariableHold Current Setup Variable Read Input Variable Home to Home Switch Variable Setup VariableHold Current Delay Time Setup Variable Increment Variable Program Instruction Read Analog Input VariableRead Encoder Index Mark Variable Initialize Parameters Instruction Joystick Enable Flag Setup FlagRead Inputs 1-4 As 1 Value Variable Label Program/Subroutine Instruction Lock User Program Setup FlagList Program Space Instruction Motion Instruction Move To Relative Position Motion Instruction Microstep Resolution Motion Variable PR MS O1 O4 Set/Print Output Logic State Variable Motor Settling Delay Time Motion VariableOn Error Handler Instruction Set Ouputs 1-4 As 1 Value Variable Set/Print Position Counter Instruction Print Selected Data/Text Instruction Postition Maintenance Enable Setup FlagEnter/Exit Program Mode Program Instruction Party Mode Enable Flag Setup Flag Pause Program Instruction Run Current Setup Variable R1 R4 User Registers User Variable Save to EEProm Instruction Resume Program InstructionReturn From Subroutine Instruction S1 S4 Set/Print I/O Point Type/Active State Instruction Set/Print I/O Point Instruction Stall Detection Mode Variable Encoder Variable Encoder Variable Trip on Input Variable Trip Enable Flag Setup FlagRead Only Stall Flag Encoder Flag Read User Variables Upgrade Firmware InstructionTrip on Position Variable Read Only Velocity Variable Motion Variable Create User Variable Name Instruction Read Only Firmware Version Factory Variable Appendix a Data Errors Error Code FaultErrors Program Errors TWENTY-FOUR Month Limited Warranty Western Region