R1 R4 User Registers User Variable | Intelligent Motion Systems 17

MNEMONIC	FUNCTION	TYPE
R1 - R4	User Registers	User Variable

DESCRIPTION

The MDrive Motion Control has four 32 bit user registers to contain numerical data. These registers may contain up to 11 digits including the sign and may be used to store and retrieve data to set variables, perform math functions, store and retrieve moves and set conditions for branches and subroutine calls.

USAGE	RANGE	DEFAULT
R<x>=<data>	-2147483647 to 2147483647	0

EXAMPLES:
R1=50000	‘Set Register 1 to 50000
‘Subroutine using a register value to perform a math function that will display axis position in revolutions rather than motor steps
‘**variable setup***
MS=256	‘set resolution to 256 microsteps/step
P=0	‘set position counter to 0
R1=51200/1	‘51200 steps = 1 rev
***Program Content*****
MR R1	‘move relative 102400 steps
H	‘Hold execution until motion stops
CL 348	‘call subroutine at address 348
‘****Sub at address 348****
R2=P	‘set Register 2 equal to the position counter
R3=R2/R1	‘set Register 3 equal to R2/R1
PR “Position = “, R3, “Revolutions”;
H 60000	‘hold for 1 minute
RT	‘return to prog

RELATED COMMANDS: —

MNEMONIC	FUNCTION		TYPE
RC	Run Current		Setup Variable
DESCRIPTION
This variable defines the motor run current in percent.

USAGE	UNITS	RANGE	DEFAULT
RC=<percent>	Percent	1to 100	25

EXAMPLE:
RC=75	‘Set motor run current to 75%

RELATED COMMAND: HC

56

Image 58

Intelligent Motion Systems 17 manual R1 R4 User Registers User Variable, Run Current Setup Variable

Contents

Operating Instructions Intelligent Motion Systems, Inc All Rights Reserved Table of Contents List of Figures Part 1 General Information and Hardware Specifications Intentionally Left Blank A t u r e S u m m a r y Standard Rotary Motor Lmax T a r y M o t o r Specification sC t i o n O v e r v i e w Control Knob LMAX2 MDI1715 N e a r M o t o r Specification sMDI1719 E e d F o r c e C u r v e 2 4 V D C MDI17 Linear ActuatorE e d F o r c e C u r v e 4 5 V D C R i v e 1 7 M o t i o n C o n t r o l a C M E S c r e w N e r a l Specification sMDI17 Acme Screws W e r S u p p l y R e q u i r e m e n t s E r m a l Specification sC o m m e n d e d I M S P o w e r S u p p l i e s A t u r e S u m m a r y MDrive23 Motion Control Specifications MDI2218 MDI2222 MDI2231 MDI23 Linear Actuator Refer to .10 for screw pitch information R i v e 2 3 M o t i o n C o n t r o l a C M E S c r e w MDI23 Acme Screws IP404MDI23 Page Intentionally Left Blank N C o n f i g u r a t i o n a n d D e s c r i p t i o n s Connector P1Y o u t a n d I n t e r f a c e G u i d e l i n e s C o m m e n d e d W i r i n g T e r f a c i n g R S 4 8 5 C o m m u n i c a t i o n s Connector P2 10 Pin HeaderT e r f a c i n g P o w e r N g l e M D r i v e RS-485 Interface, Multiple MDrive Motion Control System T e r f a c i n g I n p u t s T e r f a c i n g t h e D i g i t a l I / OE s o f t h e D i g i t a l I / O Input Functions TTL Interface to Input Group Truth Table I/O Used as a Group T e r f a c i n g O u t p u t s T e r f a c i n g a S i n g l e O u t p u t E x a m p l e s T e r f a c i n g t h e a n a l o g I n p u t M p l e U s a g e Installation Install i n g a n d U s i n g I M S Te r m i n a lS t e m R e q u i r e m e n t s I n g t h e I M S Te r m i n a l S o f t w a r e 13 IMS Terminal Upgrader Window S t r u c t i o n s R i v e M o t i o n C o n t r o l P r o g r a m m i n gE r a t i o n a l M o d e s R i a b l e s A g s Y w o r d s T h F u n c t i o n s T i o n C o m m a n d s Read IO1 Setup PR S1 Read IO2 Setup PR S2 C o m m a n d s Please Note Any program labeled SU will execute on power-up VAR CT Mnemonic Function Unit Range Syntax Example Baud I n s t r u c t i o n s , Va r i a b l e s a n d F l a g s Symbol Function T h e m a t i c a l F u n c t i o n s Acceleration Motion Variable Baud Rate Setup VariableRetrieve All Parameters Variable Branch Program Instruction Busy Flag Read Only Motion Flag Call Subroutine Program Instruction Set Counter 2 Encoder Counts Motion VariableClear Program Program Instruction D1-D5 Digital Input Filtering Variable Set Encoder Deadband Setup VariableDeceleration Motion Variable Device Name Setup Variable Drive Enable Flag Setup FlagEnd Program Execution Program Instruction Echo Mode Flag Setup Flag Encoder Enable Flag Setup FlagRead-Only Error Flag Status Flag Error Number Variable Status Variable Execute Program Program Instruction Hold Current Setup Variable Home to Index Mark Variable Setup VariableHold Program Execution Program Instruction Hold Current Delay Time Setup Variable Home to Home Switch Variable Setup VariableRead Input Variable Read Encoder Index Mark Variable Read Analog Input VariableIncrement Variable Program Instruction Read Inputs 1-4 As 1 Value Variable Joystick Enable Flag Setup FlagInitialize Parameters Instruction List Program Space Instruction Lock User Program Setup FlagLabel Program/Subroutine Instruction Motion Instruction Move To Relative Position Motion Instruction Microstep Resolution Motion Variable PR MS On Error Handler Instruction Motor Settling Delay Time Motion VariableO1 O4 Set/Print Output Logic State Variable Set Ouputs 1-4 As 1 Value Variable Set/Print Position Counter Instruction Enter/Exit Program Mode Program Instruction Postition Maintenance Enable Setup FlagPrint Selected Data/Text Instruction Party Mode Enable Flag Setup Flag Pause Program Instruction Run Current Setup Variable R1 R4 User Registers User Variable Return From Subroutine Instruction Resume Program InstructionSave to EEProm Instruction S1 S4 Set/Print I/O Point Type/Active State Instruction Set/Print I/O Point Instruction Stall Detection Mode Variable Encoder Variable Encoder Variable Read Only Stall Flag Encoder Flag Trip Enable Flag Setup FlagTrip on Input Variable Trip on Position Variable Upgrade Firmware InstructionRead User Variables Read Only Velocity Variable Motion Variable Create User Variable Name Instruction Read Only Firmware Version Factory Variable Appendix a Data Errors Error Code FaultErrors Program Errors TWENTY-FOUR Month Limited Warranty Western Region