ADDENDUM TO ISSUE 4 OF THE AXXESS MANUAL OCTOBER 1997
Page 71 of 73
key to enable the option. Or, press 2 or the NO
menukey to disable it. Then press # or ACCEPT
to continue.
—Subjectto toll restriction: To program the trunk
groupSubject to Toll Restriction option, press 4
or the SUBJECT TO TOLL menu key.When
thedisplay shows SUBJECT TO TOLL, press1
or the YES menu keyto enable the option. Or,
press2 or the NO menu key to disable it. Then
press # or ACCEPT to continue.
Page 4–131, Trunk List programming instructions:
In the last substep, the display should be ENTER
TRUNK EXTENSION (not STATION).
Page 4–140, paragraph 41.9: The Record All Incom-
ingCalls option shouldsay: Records all incoming calls
that are answered, except DID/DNIS calls.
Page 4–142 DIALED DIGITS: Add this information:
If ARS was used to place the call, the modified tele-
phone number, not the dialed digits, are shown.
Page5–34, paragraph9.5: The pa ragraph should read
as follows: If desired, the SMDR records can be re-
trieved and processed usingInter-Tel Inside Track, a
separate call accounting software package, to create
customized reports.
Page6–4, section28: Add the following entries to sec-
tion 28 of the table of contents.
G. System Serial Port Assi gnment 6–265...
H. System Serial Port Configuration 6–267.
I. T1 Diagnostics 6–269................
Page6–44, paragraph 9.82, first bullet: The fifth sen-
tenceshould say: COS designations 2–16 are program-
mable.
Page 6–47, paragraph 9.90: The first sentence should
say: The Voice Mail Information windowis shown on
the next page.
Page6–47, paragraph 9.91, first bullet: Thereis not a
“None” option when programming a Record-A-Call
Mailbox. Therefore, the correct information is as fol-
lows:
•Record-A-CallMailbox and User Keyed Mail-
box: Determine which mailbox, if any, will be
dialed automatically whenthe Record-A-Call fea-
ture is used. The Record-A-Call Mailbox can be
set to “Associated Mailbox” to call the mailbox
assignedto that station, or it can be set to any valid
mailbox number. If you do not want a mailbox
number dialed automatically when the Record-A-
Call featureis used at this station, enable the User
KeyedMailbox flag. This overrides the automatic
entry and allows the station userto enter the de-
siredmailbox number. The operation of the feature
is determined by the programmed combination of
these flags,as shown in the chart at the bottom of
the page.
Page 6–86, last bullet: The first sentence should be:
Preparea list of up to 75 hunt groups and the stations/
extension lists to be includedin them.
Page 6–93, paragraph 11.92: The database allows up
to 15 “local” area codes (not three, as stated).
Page 6–102, paragraph 11.114: The first sentence
should say: Up to 200 unique forwarding paths
(001–200) can be programmed.
Page6–114, Voice Mai l Dial Delay Timer: This timer
is for analog voice mail hunt groups only.
Page 6–158, paragraph 17.4: The third sentence
shouldbe: Ente r the desired rate in the text box (0.00 to
99.99) and select the OK command button.
Page 6–159, paragraph 17.9: The Record All Incom-
ing Calls flag should say: Selecting this check box in-
cludes all incoming calls, except DID/DNIS calls, in
the SMDR report.
Page6–162, paragraph18.3: The screen used forpro-
gramming the AXXESSORY Talk communication
porthas changed. The correct information is: AXXES-
SORYTalk programming cannot be performed until an
AXXESSORY Talk communications port has been es-
tablished in the System Serial Port Assignment pro-
gramming window (shown on page 6–265).
RECORD-A-CALLMAILBOX USER KEYED MAILBOX RESULT
“Associated” or mailbox
number Disabled The Record-A-Call Mailbox is automatically called
when the feature code isentered.
“Associated” or mailbox
number Enabled The user is prompted to enter the desired mailbox
number after the Record-A-Call feature code is en-
tered. If a number is not entered before the dialing
timer expires, the programmed Record-A-Call Mail-
box number is dialed automatically.