Chairs built before 12/01/2008 | Invacare Adjustable ASBA Seat

SECTION 5—CENTER MOUNT FOOTRESTS

Adjusting the Height of the Manual Center Mount Footrest

Chairs built before 12/01/2008

WARNING

After adjusting the center mount footrest, minimum ground clearance for the footrest in the driving position is three inches. If the center mount footrest is in the retracted position and the wheelchair is not moving, the footrest must maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.

NOTE: For this procedure, refer to FIGURE 5.2.

1.Remove the two mounting screws that secure the footrest extension tube to the extension tube housing.

2.Adjust the footrest extension tube to the desired height.

3.Align the mounting holes on the extension tube housing with the mounting holes on the footrest extension tube.

4.Reinstall the two mounting screws to secure the footrest extension tube to the extension tube housing. Securely tighten.

5.Repeat STEPS 1‐3 for the other extension tube.

	Seat Frame
	Release Lever
	Extension Tube
Mounting Holes	Housing
Mounting Holes
Mounting Screws
Mounting Holes	Footrest
	Extension Tube

FIGURE 5.2 Adjusting the Height of the Manual Center Mount Footrest -

Chairs built before 12/01/2008

Part No 1143238

19

Adjustable ASBA Seat

Image 19

Invacare Adjustable ASBA Seat Adjusting the Height of the Manual Center Mount Footrest, Chairs built before 12/01/2008

Contents

Adjustable Asba Seat Reference Documents Useful Terms Table of Contents Arms Adult Seats Junior Seats Special Notes Signal Word Meaning Special Notes All Wheelchairs Label LocationsAll Wheelchairs with Trro Wheelchairs without Trro Typical Product Parameters Adjustable Asba Seat General Guidelines Repair or Service InformationOperation Information Tire Pressure Weight Limitation Pinch Points SAFETY/HANDLING of Wheelchairs EMI Information EMI Information Safety Inspection Checklist Safety INSPECTION/ TroubleshootingTroubleshooting Center Mount Footrests Installing Removing/Installing the Manual Center Mount FootrestRemoving Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount Footrest Chairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate Angle Adjusting the Tension of the Flip Up Footplate Front Riggings Installing/Removing FootrestsPH904A, PHAL4A, 70 and PW93 Taper Adjusting the Footrest HeightPH904A and PHAL4A Front Riggings PW93 Adjusting the Footrest Height PW93 Raising/Lowering Elevating Front Riggings Replacing Heel Loops Adjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging Support Installing Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate Hinge Perpendicular and/or Inversion/Eversion Adjustment Adjusting Adjustable Angle Flip-Up FootplatesDepth Adjustment Angle Adjustment Composite Replacing Composite/Articulating Footplate Heel Loop 14 Installing/Removing Elevating Legrests Installing/Removing Elevating Legrests Raising/Lowering Elevating Legrests Adjusting Calfpads Installing/Removing the Power Elevating Legrests Power Elevating LegrestsInstalling the Power Elevating Legrests Removing the Power Elevating Legrests Adjusting the Power Elevating LegrestsAdjusting the Footplate Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf Pad Adjusting the Calf Pad Height Adjusting the Length for Power Legrest Removing/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest Actuator Right power Arms Installing/Removing Flip Back Armrests Positioning Flip Back Armrests for Use Adjusting Flip Back ArmrestsAdjusting Positioning Flip Back Armrests for User Transfer Installing/Removing the Cantilever Arms Installing/Removing the Cantilever Arms Adjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever Arms Installing/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever Arms Removing the Contoura Back Removing/Installing the Contoura BackInstalling the Contoura Back Adult Backs Removing/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura Back Adjusting the Back Angle Adjusting the Back Width Removing/Installing the Back Canes Adjusting the Back Height Removing/Installing the Back Canes Removing/Installing the Spreader Bar Removing/Installing the Spreader Bar Adjusting Spreader Bar Width Adjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat Pan Adjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side Rails Removing/Installing Side Rails Installing Side Rails Junior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty