13-2-5 Function TEST
1.This is a forced operation for TEST, Service, cleaning, etc. It is operated by pressing and holding the Fill Key for 3seconds.
2.The test works only in the Icemaking Mode. It cannot be entered from the Harvest or Fill mode.
3.Caution! If the test is performed before water in the icemaker is frozen, the ejector will pass through the water. When the Fill mode begins (Stage 4), unless the water supply has been shut off, added water will overflow into the ice bin. If the control doesn’t operate normally in the TEST mode, check and repair as needed.
4.After water is supplied, the normal CYCLE is followed : icemaking Harvest Park Position Fill.
5.Five seconds after Stage 5 is completed, the Ice Maker returns to MICOM control. The time needed to supply water resets to the pre- test setting.
Diagnosis TABLE
STAGE | ITEMS | INDICATOR | REMARKS | ||||||
|
|
|
|
|
|
|
|
| |
1 | HEATER |
|
|
|
|
|
| Five seconds after heater starts, a heater | |
|
|
|
|
|
| will go off if the temperature by sensor is | |||
|
|
|
|
|
|
|
| higher than 10°C | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
2 | MOTOR |
|
|
|
|
|
| Five seconds after heater starts, you can | |
|
|
|
|
|
| ||||
|
|
|
|
|
| confirm that a motor is moving. | |||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
3 | HALL IC I |
|
|
|
|
|
| Check if Ice Bin is full or not. | |
|
|
|
|
|
| If Ice bin is full, the motor and heater are | |||
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| off and on stand by until Ice bin is empty. | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
4 | HALL IC II |
|
|
|
|
|
| You can confirm HALL IC detection of | |
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
| start position. | |||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
5 | VALVE |
|
|
|
|
|
| Two seconds after detection of start | |
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
| position, you can confirm that valve is on. | |||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
| Return to Status prior to | Five seconds after fifth stage is | ||||||
6 | Reset | completed, The icemaker resets to initial | |||||||
TEST MODE | |||||||||
|
| status. | |||||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
13-3-1 ERROR CODES shown on Ice Maker water supply control panel
NO | DIVISION | INDICATOR | CONTENTS | REMARKS | |||||||
|
|
|
|
|
|
|
|
|
|
| |
1 | Normal | Mark time to supply | None | Display switch operates | |||||||
properly | |||||||||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
| Icemaking |
|
|
|
|
|
|
| Open or | Make sure that the wire on | |
2 | Sensor |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| each sensor is connected. | ||||
| malfunction |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
- 67 -