Chapter Two: Setting Up
Selecting SW
-Press the SET UP button to display
=Press the MULTI CONTROL (fi/%) button to select ON or OFF.
~Press the SET UP button to proceed to “Adjusting the speaker volumes” below. To exit from setting, press the SET UP button repeatedly until “SETUP FIXED” is displayed.
For details on the SW
2.Adjusting the speaker volumes
Adjust the volume balance between the speakers in the sys- tem by actually listening to them. See page 39 for details.
1Minimize external noise in the listening room.
2Position yourself in a place where you usually listen to music or view video.
3Perform operation in step ~ of procedure 1 above. "TEST TONE OFF" is displayed.
4Press the MULTI CONTROL (fi/%) button to select ON, then press the SETUP button.
When setting the speaker levels, be careful against the
The speaker volume adjustment display appears and test noise is generated from the front left speaker (“L 0 dB” displayed). Listen to the volume of the noise carefully.
5When the test noise moves to the center speaker and “C 0 dB” is displayed, adjust the volume to the same level as the front left speaker by pressing the MULTI CONTROL (fi/%) button.
6Similarly, adjust the volumes of the “R” (front right), “SR” (surround right), “SBR” (surround back right), “SBL” (surround back left) and “SL” (surround left) speakers.
Do not adjust the “SW” (Subwoofer) volume using the test noise. It should be adjusted while listening to ordinary music.
7Press the SET UP button to display “BASS PEAK OFF”
8Press the MULTI CONTROL (fi or %) button, then displayed
The test noise is output. Press the MULTI CONTROL (fi/%) button to set its level to a level just before the speaker sound starts to be distorted.
9Press the SET UP button to proceed to “Selecting the speaker distances” below. To exit from setting press the SET UP button repeatedly until “SETUP FIXED” is displayed.
3.Setting the speaker distances
Measure the distance between each speaker and the listen- ing position you frequently use. See page 38 for details.
1After the operation of 9 in procedure 2 above, the speaker distance setting display appears.
2 When “L 3.0m/10ft” is displayed, correct the dis- tance of the front left speaker from you using the MULTI CONTROL (fi/%) button.
3Press SET UP button to display “C 3.0m/10ft” and correct the distance of the center speaker from you using the MULTI CONTROL (fi/%) button.
4Similarly, set the distances of the “R” (front right), “SR” (surround right), “SBR” (surround back right),“SBL” (surround back left), “SL” (surround left) and “SW” (Subwoofer) speakers.
5Press the SET UP button repeatedly until “SETUP FIXED” is displayed.
Storing Radio Stations in Memory (optional)
Radio stations can be preset in the memory in the receiver and recalled by a
The memory in the receiver cannot store the station names. To store the station names, use the PowerTouch. (For de- tails, see “Storing Radio Stations in Memory (optional)” on page 41.)
Storing RDS Stations Automatically:
1.Press the INPUT SELECTOR ¤ or ‹ button to select the Tuner input.
2.Press the BAND button to select the FM band.
3.Press and hold the MEMORY button for more than 2 seconds. The receiver locates and stores any FM stations broadcasting an RDS signal. This process can take a few minutes to complete; please be patient. While the re- ceiver is searching, “AUTO MEMORY” display blinks. 47
Storing Stations Manually:
1.Press the INPUT SELECTOR ¤ or ‹ button to select the Tuner input.
2.Press the BAND button to choose the receiving band.
3.Press the AUTO button to select AUTO TUNING or
MANUAL TUNING.
4.Press the MULTI CONTROL (fi/%) button to tune the station you want to store.
5.Press the MEMORY button.
6.Press the P.CALL (fi/%) button to display the desired preset number.
7.Press the MEMORY button again to complete the pre- setting.
8.To preset other stations, repeat steps 2 to 7 for each station you want to store.
Seting Up
