Windows Peer-to-peer Print Driver, Setup | LevelOne WPS 0100

Windows Peer-to-peer Print Driver

With this printing method, print jobs are stored (queued) on your PC, and then sent to the LevelOne Printer Server when it is available.

Setup

Before performing the following procedure, the LevelOne Printer Server must be installed on your LAN, and configured as described in Chapter 3. Both the LevelOne Printer Server and the attached printer should be powered ON.

1.Insert the supplied CD-ROM into your drive. If the setup program does not start automatically, run SETUP in the root folder.

2.Select the Installation icon, then choose the User option in the "Setup Type" screen. This will install the Peer-to-peer Print Driver.

3.Follow the prompts to complete the installation. (Refer to the Windows section of Chapter 8 - Troubleshooting if there is a problem with the installation.)

4.The Print Driver Setup will then run.

5.The LAN will be searched for LevelOne Printer Servers, and a screen like the following will be displayed.

∙If desired, change the Workgroup name and click Refresh.

∙Select List all LevelOne Printer Servers to list all LevelOne Printer Servers, regardless of Workgroup.

∙The name of the attached printer will be displayed if possible. If "No printer" is displayed, check that the printer is properly connected and powered on.

Figure 2: Printer Port Setup (Peer-to-peer Print Driver)

Page 16

Image 19

LevelOne WPS 0100, WPS-100USB manual Windows Peer-to-peer Print Driver, Setup

Contents

User Guide Table of Contents Appendix a Specifications TroubleshootingAppendix B Network Server Configuration Introduction Features Safety Instructions Models Package Contents WPS-0100 LAN LED To generate a Diagnostic print out LED IndicatorsDiagnostic Push Button To restore the factory default settingsPage Procedure LAN Installation Check the LEDs LevelOne Printer Server ConfigurationUsing the Windows Wizard Procedure Alternatives to the Windows Wizard Wireless ConfigurationIf the desired LevelOne Printer Server is not listed Quickset Advanced Configuration and Management WEP Settings Client PC ConfigurationWireless Settings for client PCs Ad-hoc Mode Infrastructure Mode Which printing method should I use? Printing MethodsChecking your Network Protocols Windows Network Configuration Windows Peer-to-peer Print Driver Setup If your LevelOne Printer Server is not listed Configure Printer Port Port Options Management Banner PortRetry Interval Network Neighborhood Windows SMB Printing Printing from MS-DOS Programs Windows with Server-based Print Queues Ndps Manager Client Windows using Ndps Software Requirements AppleTalk SetupAdvanced Setup and Management Macintosh AppleTalk Communication Protocol. Enter no for Ascii or YES for Binary AppleTalk SettingsPage Additional Recommendations BiAdmin Management UtilityInstallation Requirements Main Screen OperationGroups Status Icons Device List Device Information Configuration IconsTCP/IP Configuration AppleTalk Configuration Menu Options InitDevice Menu Print Test Configuration MenuDiagnostics menu Control Menu Preparation Web Interface Setup Configuration Screens Connecting to the LevelOne Printer ServerAppleTalk Response Time If ErrorNetBEUI Domain Name NetWare LevelOne Printer Server ModeGeneral Management Stations Snmp Simple Network Management Protocol Connection Trap Receivers Server Name Configure ServerPassword Enable Protocols Wireless Screen WEP Data Privacy Configuration 128 Bit AuthenticationKey Printer Ports Serial Port ConfigurationOther Screens Server Status IPP Server Configuration Special FeaturesInternet Printing Protocol IPP IPP Client Configuration Windows 95/98/ME/NT IPP Client Setup Windows 95/98/ME/NTInstalling from the CD-ROM Installing using IPPCLIENT.EXE Open the Printers folder Start Settings Printers Changing the IPP Port Settings Parallel Port 3 if exists IPP Client Setup Windows Windows 2000 No printer driver Using IPP Printers Internet LevelOne Printer Server Internet Mail PrintingSystem Requirements Mail Server Internet Mail Printing Configuration User Software Installation User SoftwarePort Name Using the new Port Printing through the Internet Canceling a Print JobChecking the Printer Driver Trap Receiving Station Settings Configuring the LevelOne Printer Server for SnmpSnmp Settings Management Station Settings Required configuration Wireless ConfigurationModels WPS-0100 & WPS-0100USB WEP Settings BiAdmin Wireless Screen Enabled WEP DisabledEncryption Link Info Screen Wireless Link Info Screen If using TCP/IP TroubleshootingHardware & LAN Problems Problem No All the LevelOne Printer Servers LEDs are off AppleTalk Macintosh Page Novell NetWare To remove an existing printer port installation Windows Printing ProblemsPage ∙ Then select File Properties Details Problem No WPS-0100 SpecificationsGeneral Specifications Environmental Specifications all Models Other Models Parallel Port Pin Assignments Protocol Support Feature Support Preparing for TCP/IP Printing Network Server ConfigurationRegulatory Approvals Windows NT Server Windows Adding a TCP/IP Remote Printer Setup Wizard Configuration Methods Bindery or NDSWindows 2000 Server Other Methods Configuration DataBiAdmin Novell Remote Printer Mode Creating an Ndps Manager Object Setup for Ndps NetWareNovell LevelOne Printer Server Mode Overview At the Identification page, click the Printer Agent List Creating an Ndps Printer Agent Select Novell Printer Gateway in the Gateway Type. see above ∙ LPD ∙ FTP Unix Systems