Manuals / Brands / Computer Equipment / Switch / MGE UPS Systems / Computer Equipment / Switch

MGE UPS Systems STS 200A, STS 400A, STS 600A CB1, CB2, CB4, CB3, CB5, LOAD, ALARM, SOURCE, SOURCE, SOURCE, SWITCH, SWITCH, IN SYNC, PREFERRED

1 66

Download 66 pages, 2.74 Mb

Installation and User Manual

Figure 3-4: LED Mimic Diagram.

SOURCE #1

SELECTED AS PREFERRED- YELLOW LED

SOURCE #2

SELECTED AS PREFERRED- YELLOW LED

SOURCE #1

AVAILABLE GREEN LED-LIT WHEN SOURCE #1 POWER IS APPLIED TO SOURCE S1 INPUT

SOURCE #1

INPUT C.B.

GREEN LED-LIT

WHEN CLOSED

SUMMARY ALARM-RED LED

STATIC SWITCH #1 GREEN LED-LIT WHEN SCR1 ON

SOURCE 1			SOURCE 2
AVAILABLE			AVAILABLE

	S1	S2

PREFERRED

SOURCE

IN SYNC

CB1	CB2
ALARM
SWITCH 1	SWITCH 2

SOURCE #2

AVAILABLE GREEN LED-LIT WHEN SOURCE #2 POWER IS APPLIED TO SOURCE S2 INPUT

IN SYNC-

GREEN LED

SOURCE #2

INPUT C.B.

GREEN LED-LIT

WHEN CLOSED

STATIC SWITCH #2 GREEN LED-LIT WHEN SCR2 ON

CB4	CB3	CB5
SOURCE #1		SOURCE #2
BYPASS C.B.		BYPASS C.B.
GREEN LED-LIT		GREEN LED-LIT
WHEN CLOSED		WHEN CLOSED
OUTPUT POWER	LOAD	STS OUTPUT
TO LOAD		ISOLATION C.B.
GREEN LED-LIT		(CB3A AND/OR CB3B)
WHEN OUTPUT		GREEN LED-LIT
POWER IS ON		WHEN CLOSED

86-504004-00 B03

Operation

3 —13

Contents

w w w . m g e u p s . c o m Standard Features Installation and User Manual Page MGE UPS SYSTEMS, INC. 1660 Scenic Avenue Costa Mesa, CA 92626 (714) NOTE How to use this manual and Symbol Usage CAUTION IMPORTANT NOTE UPS SERIAL NUMBER: MODULE SERIAL NUMBER: BATTERY SERIAL NUMBER: ADDITIONAL MODULES SERIAL NUMBERS: Contents Section 2 Setup and Installation Section 3 Operation Glossary Reorder Form MGE Warranty & Proprietary Rights for Three Phase Products Warranty and Product Registration Customer Care Center - Single Phase Products Figures Tables On-SiteQuick Start First steps by an on-sitequalified Technical Engineer Required Equipment and Tools Step 1 Unpacking Figure QS-1 Page Connect Input Power from Two Sources NOTE: Step 4 Arrival of MGE Field Engineer Optional Steps Introduction 1.0Scope 1.1Reference Manuals 1.2Section Descriptions 1.3General Description 1.4Epsilon STSTM System Characteristics 1.4.1PMM2 Plus and PMM2 Ultra 1.5System Major Components Hard Keys Input Power SCR Switch Soft Keys Static Transfer Switch (STS) 1.6Single Line Diagram 1.7System Specifications 1.7.1Electrical Electrical Characteristics 1.72Electrical Cable Access and Connections 1.7.3Connecting Power Cables 1.7.4Accessing Electrical Connections # OF CABLES PER MINIMUM CABLE LUG CONDUIT STS RATING (AMPS) DIA (QTY.) Page Setup and Installation 2.0Scope 2.1Cabinet Placement and Environment Data Rate 2.2Clearances and FootPrint 2.2.1Conduit Plate Location (bottom entry) 2.3Source #1 AC Input Connections 2.3.1.Source #2 AC Input Connections 2.3.2AC Output Connections 2.3.3Remote Emergency Power Off (REPO) Cable Connections 2.3.4Remote Source Loss Test Cable Connections 2.3.5Connection of the Relay Communication Card 2.3.6Characteristics of the Output Contacts 2.3.7Characteristics of the Input Contacts 2.3.8Removing the Communications Card Cover 2.3.9Replacing the Cover 2.4Setting Operation Mode 2.5Setting the Output Relay Contacts and Input Switching States 2.5.1Connection of the JBUS Communication Card 2.6Check Points Before and After Start Up 2.6.1Pre-StartUp Safety Check List 2.6.2Post-StartUp Safety Check List Operation 3.0Scope 3.1Preparation for Operation 3.2Pre-StartUp Safety Check List 3.2.1Normal Start Up Procedure 3.2.2Post Start Up Safety Check List 3.2.3Shutdown Procedure 3.3Transfer Operations 3.3.1Automatic Transfers 3.3.2Manual Transfers 3.3.3Automatic Retransfers 3.3.4Transfer Authorization/Prohibition 3.4Maintenance Bypass/Molded Case Switches/Live System Test 3.4.1Switch Arrangement 3.4.2Electrical Bypass Switch Interlock 3.4.3Electric Input-BypassSwitch Interlock 3.4.5Live System Test (Except with 4-InterlockSystem) 3.4.6EPO 3.5Preferred Source Selection (Symmetrical Operation) 3.6Sensing and Transfer Times 3.7Overload Operation 3.9Open SCR Protection 3.10Source Cross-ConnectionProtection 3.11Bypass Procedure Bypass Load to Source #2 Return to Normal Operation (load on Source #2) Test Mode (Except with 4-InterlockSystem) supply circuits are still live and power is provided for indicator lights and emergency power off circuits 3.12Front Panel 3.13Front Display Interface Panel Preferred = 0° Page PREFERRED IN SYNC CB1 CB2 ALARM 3.14Operator Interface Screens 3.15Epsilon STS™ Customization Product Name MGE Warranty & Proprietary Rights Statement for Three Phase Products User Information Product information Warranty Extension (Warranty+) MGE Customer Care Center - Three Phase Products Technical Support: Customer Care Center: 1-800-438-7373 (Hours: 24/7) Customer FAQ Page Glossary Term used Definition / Meaning Page Page Page Use this form Installation and User Manual Page Page Contact MGE United States MGE UPS SYSTEMS Canada MGE UPS SYSTEMS #9,2789ThamesgateDrive Mississauga,ONL4T4E8