Section - 5 Advanced Topics | Johnson Millennium |
Setting up an LFO
To set up an LFO that is linked to an effect parameter, the procedure is as follows:
1.Enter the Assign mode by pressing the <Assign> button.
2.Use the <Page> knob to scroll to the LFO page. The display looks something like:
2 | LFO |
|
|
|
|
|
| WvForm Speed | |||||||||
| 1msdB%kHz |
| OffmsdB%kHz |
| SinmsdB%kHz |
|
|
| 006 Hz | ||||||||
1 | 2 | 3 | 4 | ||||||||||||||
LINK CHANGED |
|
| LINK CHANGED |
| LINK CHANGED | LINK CHANGED | |||||||||||
|
|
| WAH TUBE EQ |
| GATE |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| L/R OUTS | |||||||
FACTORY USER |
|
|
|
|
|
|
| # |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
BANK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
PAGE17 OF 19 b |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| L/R OUTS |
3.You can use the <1> knob to select which of the two LFOs you want to adjust.
4.Use the <2> knob to turn the LFO on or off.
5.Use the <3> knob to change the selected LFO's waveform. You can select either SINe, TRIangle, SPecial1 or SPecial2.
6.Use the <4> knob to adjust the speed of the LFO cycle.
Any parameters assigned to the LFOs will now follow the modulating waveform of the LFO you have selected.
Setting up a Dynamic Modifier
1.Enter Assign mode by pressing the <Assign> button.
2.Use the <Page> knob to scroll to the first of two Dyn pages. The display looks something like:
2 | Dyn |
|
|
|
|
|
| LoThrs HiThrs | ||||||||||
| 1msdB%kHz |
| OffmsdB%kHz |
| 0 msdB%kHz |
|
| 0 |
|
| ||||||||
1 | 2 | 3 | 4 | |||||||||||||||
LINK CHANGED |
|
| LINK CHANGED |
| LINK CHANGED | LINK CHANGED | ||||||||||||
|
|
| WAH TUBE EQ |
| GATE |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| L/R OUTS |
| |||||||
FACTORY USER |
|
|
|
|
|
|
| # |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
BANK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
PAGE 18OF 19 b |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| L/R OUTS |
3.You can use the <1> knob to select which of the two Dyns you want to adjust.
4.Use the <2> knob to turn the Dyn on or off.
5.Use the <3> knob to set the threshold above which dynamic modification of the parameter begins.
6.Use the <4> knob to set the point at which maximum parameter modification occurs.
7.Use the <Page> knob to scroll to the next Dyn page.
58
User Guide