Miller Electric Auto Axcess 675 specification

LED	Status	Diagnosis

24	On	Input signal On from relay K4 to indicated wire stuck in weld joint

	Off	Input signal Off from relay K4 to indicate wire is not stuck in weld joint

25	On	Indicates +5 volts dc is present on automation interface module PC9

	Off	Indicates +5 volts dc is not present on automation interface module PC9

26	On	Input signal on from relay K5 for flow (shielding gas or coolant) present

	Off	Input signal off from relay K5 for flow (shielding gas or coolant) not present

27	On	Indicates −15 volts dc is present on automation interface module PC9

	Off	Indicates −15 volts dc is not present on automation interface module PC9

28	On	Indicates +15 volts dc is present on automation interface module PC9

	Off	Indicates +15 volts dc is not present on automation interface module PC9

29	On	Input signal on from relay K6 for arc detected

	Off	Input signal off from relay K6 for no arc detected

30, 31	On	See Network Status Table in Section 7-12

	Off	See Network Status Table in Section 7-12

32	On	Input signal on for aux. relay energized

	Off	Input signal off for aux. relay energized

33	On	Input signal on touch sensor touch detected

	Off	Input signal off touch sensor touch not detected

OM-201 540 Page 43

Image 47

Miller Electric Auto Axcess 675 Input signal on from relay K6 for arc detected, Input signal on for aux. relay energized

Contents

File Advanced Manufacturing Systems OM-201 540KProcesses Description From Miller to You Table of Contents Warranty HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can kill Flying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosion Moving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injury About Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF Information UNE Décharge Électrique peut entraîner la mort Symboles utilisés LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-201 540 Dimensions And Weight − InstallationSpecifications Overheating Duty Cycle And OverheatingVolt-Ampere Curves 100% Duty Cycle At 675 Amperes Do not stack units. Beware of tipping Connection DiagramSelecting a Location Movement Do not move or operate Tipping Rear Panel Receptacles And Supplementary Protectors Incorrect Installation Connecting To Weld Terminals Selecting Weld Cable Sizes Socket Information Peripheral Receptacle Functions Motor Control Receptacle Functions Normal Operating Electrical Service GuideHz Three Phase Input Voltage Input Amperes At Rated Output Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Program No Output a Output B Output C Remote Program SettingTouch Sensor Operation Remote Program Select Operational Terms − Operation Postflow StartWeld Crater Gas Type LED Wire Type LEDFront Panel Controls See Section Process LED STL Xxxx Robot Type Front Panel SwitchesRobot Abbreviations Manufacturer Robot Abbreviation 100 IPM 1000 IPM Robot Calibration ModeSchedule Sample Auto-Calibration Routine For Motoman Robot Robot Auto-Calibration Sample ProgramsActual Motoman Welder Condition File Weld Data Sample Auto-Calibration Routine For Fanuc RobotSample Auto-Calibration Routine For ABB Robot Accu-pulse Reset ModePulse Mild Steel Blowing Out Inside Of Unit − MaintenanceRoutine Maintenance Exploding Parts can cause injury − Safety Precautions for ServicingShock Hazard from testing Servicing Hazards California Proposition 65 Warnings Set Value Mode − Troubleshooting Diagnostics Indicates an over On errorIndicates a trigger closed error Indicates RMD demo is done Removing Cover and Measuring Input Capacitor Voltage Status Diagnosis Process Control Module PC4 Diagnostic LED’sDiagnostic LED’s On Process Control Module PC4 Diagnostic LED’s On Wire Feed Module PC6 Diagnostic LED’s On User Interface Module PC7 User Interface Module PC7 Diagnostic LED’s LED32 Automation Interface Module PC9 Diagnostic LED’sLED33 Diagnostic LED’s On Automation Interface Module PC9 Input signal off for aux. relay energized Input signal on from relay K6 for arc detectedInput signal off from relay K6 for no arc detected Input signal on for aux. relay energized Circuit board is operating normally Network And Module Status LED’s Network Status LED’sModule Status LED’s Red Trouble Remedy Troubleshooting Circuit Diagram For Welding Power Source 1 − Electrical Diagrams 198 992-G Part 1 Circuit Diagram For Welding Power Source 2 198 992-G Part 2 Circuit Diagram For 72 Pin Robot Interface 219 266-C Circuit Diagram For Peripheral/Motor Interface 219 267-B − Fig − Parts List16 − Fig Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Description Quantity Page Page Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact