Manuals / Miller Electric / Power Tools / Welder

Miller Electric IH, TS manual Load File, Date Setup

Models: TS IH

1 76

Download 76 pages 57.26 Kb

Page 54

7-3. Restoring Recorder Configuration From A Floppy Disk (For 5100 Digital Recorder)

Login as Engineer.

Touch top left corner (Logged Out) or (User).

Touch Blue text (pull down menu) next to User.

Touch Engineer.

Touch Password field.

Touch Numeric.

Touch 1, then 0, then Ok.

7-3-1. Load File

Insert digital recorder configuration disk into recorder.

Touch key in bottom right corner to open Root Menu.

Touch Operator.

Touch Save/R.

Touch Restore.

Touch field next to File Name.

Touch up folder.

Touch \Floppy\ (Highlights yellow).

Touch down folder.

Touch the desired 5100 Config file (####.uhz).

Touch Open.

7-3-2. Date Setup

1.Touch System.

2.Touch Locale.

3.Touch pull down next to Country.

4.Touch appropriate country.

5.Touch pull down next to Time Zone.

6.Touch appropriate time zone (i.e. CST Central). See “http://www.timeanddate.com” for additional information.

7.Set DST (Daylight Savings Time) if applicable. Place an “X” in the box next to “Use Summertime (DST)” to enable this option.

NOTE

In general, for those locations that observe DST: DST begins at 2:00 am on the first Sunday in April. DST ends at 2:00 am on the last Sunday in October.

See “http://deil.lang.uiuc.edu/web.pages/holidays/DST.html for exceptions.

8. Touch Apply.

OM-203 185 Page 50

Image 54

Miller Electric IH, TS manual Load File, Date Setup

Contents

Description OM-203 185FProcesses File Induction Heating From Miller to You Table of Contents Resetting All RAM Variables In The Event Of Display Errors Induction Heating Hazards − Safety Precautions − Read Before UsingSymbol Usage Electric Shock can kill Principal Safety Standards California Proposition 65 Warnings EMF Information About Pacemakers − Mesures DE Securite Pour LE Chauffage PAR Induction LE Chauffage PAR Induction peut être dangereuxLE Chauffage PAR Induction peut provoquer un incendie DES Organes Mobiles peuvent provoquer des blessures Porteurs de stimulateur cardiaque, restez à distance En ce qui concerne les stimulateurs cardiaques − Introduction IH/TS Installation − InstallationSpecifications Specification Description Connecting To Power Source Input 14 Pin Information For Receptacle RC1 Connecting 25kW System Cords And Cables FrontRear Cooler Connecting 5kW System Cords And CablesFrontRear Such as grinders, drills, lights, etc Connecting External Device − Components and Controls IH/TS Front Panel IH/TS Rear Panel 200.0 Controller IH/TS Setup Select Power Source − Setup and OperationSafety Equipment Parameter Display Locale Setup Time Date Setup − Digital2-2 Login As Engineer 2-1 Digital Recorder Controls Go To Home Screen Time And Date SetupLogin As User Channel Cycling On/Off And Notes Run List Sub-Menu Definitions OperationController Display Definitions Name Controller Operation Segment Type Definitions Programming The 2408 ControllerProgram List Terms And Definitions Setpoint remains constant for a specified period Example Pre−heat Profile Ramp rate Example Stress Relief ProfileStep to 600 F Deg/ hr Ramp to 800 F Ramp to 600 F Example Multi−Step Stress Relief ProfileRamp to 800 F @ 400 /hr Ramp to 1250 F Deg/hr Profile Set-Up Worksheet Sets output to Batch Recording Using 5100 Digital Recorder Begin Batch recording -3-3-1. Login As UserStart Recording Stop Recording Saving Data To a Disk Recommended After Each Batch Network Connection Windows 95, 98, ME Changing IP Address To Connect The IH/TS For WindowsDownloading Files From Recorder Troubleshooting Connection Problems For Windows 95, 98, ME Running a Program To Preheat Or Stress Relief Recovering From An Interruption OP1 SP2 Viewing Data In Review Software Installing Review Software And First Time SetupReview software first time setup screen Backing Up The Database Running Review Software Start Review softwareSelect Transfer Files Select Files Single File With Batch Name Select OK Single File With No Batch Name Select Start Transfer Multiple Files With Batch Names Multiple Files With No Batch Names Select File Select New Chart Select Add Point Scrn14 Select OK to view chart These steps must be done Scrn20 Select OK Comment becomes part of the chart Select Save File name becomes Part of the chart Select File Select Print to print entire profile on one Scrn30 Typical Profile Chart Printout − Configuring Controller and Recorder For each Channel Number Select Channel Number Date Setup Load File Time Setup Login As UserGo To Home Screen Troubleshooting − Maintenance & TroubleshootingRoutine Maintenance Months Goto ConF, IA ConF Module 1 Config. See Section If display flashes no.io again, or ifBefore 10 degree window is See Section When touched, but does notIs complete, turn Ihts power off and back on again Advance to next screen Diagnostic Procedures For IH/TS OM-203 185 5100V Recorder Displays Channel Error Resetting All RAM Variables In The Event Of Display Errors Press Page to Press Scroll Factory Set ParametersController Version Number Version Number Controller Edit Parameters Varies Controller Full Parameters Prior To VersionNavigation Across Scroll Down Home List Output List Configure Parameters Prior To Version ControllerNavigation Across Controller Full Parameters Effective w/Version OM-203 Navigation Across Scroll Down Home List Configure Parameters Effective w/Version Fluke-714 Thermocouple Calibration Certification ProcedureType-K Mini Connector Calibrator − Electrical Diagrams Circuit Diagram For IH/TS − Parts List Complete Assembly 198 Page Page Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s