4. TV Operation and Features

29

Remote Control, continued

Record/Playback Keys

Use any of these methods to enable the recording and playback commands:

Program the remote control for your DVR, VCR, or DVD player/recorder and set the slide switch to VCR, DVD, CABLE/SAT, or AUDIO as appropriate.

On LT-40134, LT-46144, and LT-52144 model TVs: Perform NetCommand IR “learning” for the device.

Check HDMI devices for compatibility with the TV’s NetCommand for HDMI feature (see below).

23. (Pause): Pauses a VCR, DVR, or DVD. See pre- vious page for use during TV viewing.

24. (Play): Plays a VCR, DVR, or DVD.

25. (Record): Records with a VCR or DVR.

26. (Stop): Stops play of a VCR, DVR, or DVD.

27. (Reverse): Rewinds a VCR. Reverse scans a DVR or DVD.

28. (Forward): Fast forwards a VCR. Forward scans a DVR or DVD.

Note: To operate other audio/video devices:

See Appendix D, “Programming the Remote Control.”

See chapter 6, “NetCommand,” for NetCommand IR “Learning” of device keys.

For HDMI devices compatible with the TV’s NetCommand for HDMI feature, see below.

NetCommand for HDMI Devices

The TV’s remote may operate some functions of compatible HDMI devices able to receive commands through the HDMI cable. Test your equipment with the TV’s remote to find out which commands are sup- ported. See below for commands that may be avail- able, depending on the individual device.

Note: On models LT-40134, LT-46144, and LT-52144, you can add commands using NetCommand IR “Learn- ing” after connecting and placing IR emitters for the devices.

Press PLAY on the device itself to:

Turn on the TV if not already on

Switch to the device (no need to display the Input Selection menu)

Begin play of the device

VCR, DVD, and DVR functions that may be available:

Record/

Menu

Channel Tuning

Other

Playback

Navigation

 

 

 

 

 

CH/PAGE

 /

Guide

 

Enter

Digits 0–9,

F1 (content)

 

CANCEL

 

ENTER

MENU

 

CANCEL (to cancel)

Resetting the Remote Control

If the slide switch is set to TV and the TV does not respond properly, reset the remote control.

1.Press and hold POWER for several seconds until the button blinks twice and goes off.

2.Release the POWER button.

3.Press keys 0 0 9 3 5 and the POWER button will blink twice when you finish entering the code. While entering the code, pause for a moment between each key press to ensure it is recognized.

Care of the Remote Control

Use only alkaline batteries (never use old & new batteries together).

Be within 20 feet of the equipment.

Do not press two or more buttons at the same time unless instructed to do so.

Do not allow unit to get wet or become heated.

Avoid dropping on hard surfaces.

Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth.

ChannelView™ Channel Listings

ChannelView (or TV Guide Daily, if active - model LT-40134 only) channel listings are accessible via the GUIDE key. For TV Guide Daily details, see Appendix C.

ChannelView displays only digital channel names and program information as sent by broadcasters or local cable providers and may be incomplete.

To receive ChannelView/TV Guide updates, keep Energy Mode set to Fast Power On, set TV Clock, and leave the TV powered off for a while each day. Note: Digital channel listings are updated while viewing.

Using ChannelView

Feature

Press Key

See ChannelView listings

Press GUIDE.

from ANT 1 or ANT 2.

 

 

 

 

Close ChannelView

Press GUIDE or EXIT.

 

 

Scan channels one by one.

Press & hold or .

 

 

Scan channels quickly.

Press & hold CH/PAGE  /  .

 

 

 

Jump to listings for a spe-

1.

Enter the channel

cific channel.

 

number (see numbers

 

 

in upper left).

 

2.

Press ENTER.

 

 

See more of the program

Press INFO.

description.

 

 

 

 

Move navigation to the

Press .

program guide.

 

 

Move navigation to the

Press .

channel guide.

 

 

 

 

Tune to the highlighted

Press ENTER.

channel.

 

 

Page 29
Image 29
Mitsubishi Electronics LT-40133 manual ChannelView Channel Listings