Mitsubishi Electronics WS-73517 manual Back Panel, IEEE-1394 Input/Output, Digital Audio Output

Back Panel

11.

		ANT-2	ANT-1
		AUX	MAIN
SERVICE	IEEE1394			DIGITAL
				AUDIO
PORT	INPUT/OUTPUT			CableCARDTM SLOT

– (DTV/CABLE /VHF/UHF) –

DVI

Analog Audio

Digital Video

Digital Audio

10.9.

INPUT

MONITOR OUTPUT

1

2

AUDIO/VIDEO 1

AUDIO 2

S-VIDEO

VIDEO

AUDIO-

LEFT/

(MONO)

IR EMITTER

8.

AUDIO-

NetCommand R

RIGHT

COMPONENT

YPbPr (480i/480p/1080i)

1

2

SERVICE WARNING

Y

CAUTION: TO MEASURE SECOND

ANODE VOLTAGE USE A HIGH VOLTAGE

METER CONNECTED FROM ANODE LEAD

TO CHASSIS ONLY. DISCHARGE HIGH

Pb

VOLTAGE TO CHASSIS ONLY, NOT TO

EXTERNAL GROUND.

WARNING: HANDLE WITH CARE. HIGH

VACUUM PICTURE TUBE IS DANGEROUS

Pr

TO HANDLE.

REFER SERVICING TO

Q U A L I F I E D S E R V I C E P E R S O N N E L .

AUDIO-

REPLACE WITH A TUBE OF THE SAME

TYPE NUMBER FOR CONTINUED SAFETY.

LEFT/

X-RAY PRECAUTION: THIS PRODUCT

(MONO)

I N C L U D E S C R I T I C A L M E C H A N I C A L

AND E LE CTRICAL PARTS WHICH ARE

AUDIO-

ESSENTIAL FOR

X-RADIATION SAFETY.

RIGHT

F O R C O N T I N U E D S A F E T Y R E P L A C E

C R I T I C A L C O MP O N E N T S

I N D I C AT E D

IN THE SERVICE MANUAL

ONLY WITH

E X ACT R E PLACE ME NT PART S GI V E N

IN THE PARTS LIST. REFER TO SERVICE

MANUAL FOR OPERATING HIGH VOLTAGE AT

MINIMUM BRIGHTNESS, MEASUREMENT

PROCE DURE S AND PROPE R SE RV ICE

ADJUSTMENTS.

1. 2. 3. 4. 5. 6. 7.

1. IEEE-1394 Input/Output

Use these jacks to connect the TV to external IEEE 1394 digital products by means of a single cable. There are two jacks on the back panel for all models. For WS-55517, WS-65517 and WS-73517 there is an additional jack on the front panel. IEEE 1394 connections provide a high degree of flexibility when connecting your NetCommand® controlled system. Detailed information regarding IEEE 1394 connection requirements are in Chapter 4.

2.Antenna (ANT-1 MAIN, ANT-2 AUX)

ANT-1 MAIN and ANT-2 AUX can each receive both digital/analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable channels.

Your primary viewing signal source should be connected to ANT-1 MAIN. ANT-1 MAIN must be used to view premium subscription cable TV service authorized by the CableCARD™ access card. The CableCARD access card is provided by your local cable company. ANT-2 AUX can continue to receive over-the-air or non-scrambled cable signals.

3. Digital Audio Output

This output will automatically send Dolby® Digital audio from digital channels and IEEE 1394 devices to a digital Audio/Video receiver. Connect this output to the A/V receiver’s coaxial digital audio input. This output will automatically turn off when viewing an analog channel or device. HDMI digital audio signals are not sent by this output. Use Monitor Output Audio 2 to send analog signals and HDMI audio signals to your A/V receiver.

Some digital cable channels send MPEG-1 digital audio instead of Dolby Digital, however, not all A/V receivers can decode MPEG-1 digital audio. This can cause the A/V receivers to produce a loud noise that can damage speakers. For this reason, the TV will automatically turn off the digital audio output when tuned to a channel or device that has MPEG-1 digital audio and send it to the A/V receiver as analog left and right audio from Monitor Output.

10