Mitsubishi Electronics WS-73517, WS-65517, WS-55517 manual Troubleshooting

Troubleshooting, continued

	Problem	Possible Solution
30.	A program recorded on your TV is distorted	• TV was set to Anamorphic when program was recorded.
	when played on a 4:3 TV.	Record programs in Cropped mode if playing back on a 4:3 TV.
31.	Excessive digital artifacts.	• The IEEE 1394 cable is too long (15 feet between devices is the
		maximum length).
		• There may be a slow device in the middle of the IEEE 1394 network.
		Move the slow devices to the end so that connections for faster
		devices do not pass through them.
32.	Cannot see a picture from a DV Camcorder.	• Go to Device Selection menu and select analog connection.
		• Connect the DV Camcorder to analog input (for example, Input-3).
		Select Setup from the main menu, then Change. At the Change
		screen, select the camcorder. On the Name screen, check Analog
		Connection. Select the device and on the following screen, select
		which analog input was used, and check audio and/or video.
33.	DVCR analog/digital problems.	• If the tape is currently playing but no picture displays, you may have a
		mismatch of the media with the display. Press the DEVICE key to
		display the Device Selection menu. Press ENTER for the DVCR
		device. If digital is selected, try analog, or if analog is selected, try
		digital.
34.	D-VHS recordings for digital cable have drop-	• Digital cable signals on IEEE 1394 can exceed the data rate
	outs (loss of picture or sound), or no playback.	standards supported by DVCR.
35.	TV is out of focus.	• Focus is out of alignment. Align Convergence.
36.	Red or blue color is “bleeding” or shadowing	• Focus is out of alignment. Align Convergence.
	images.
37.	There is no audio and video from the IEEE 1394	• The device is not turned on - turn the device power on.
	device.	• No media (tape or disc) is inserted into the device.
		• The media is blank (has no recording).
		• The play command failed - Try pressing play again on the device’s
		remote control or front panel.
		• The device is already in use (for example: the device is currently
		recording).
		• The source is copy-protected or violates copy protection.
		• The device’s digital video signal is not supported by the TV, such as
		DV video, common with camcorders. Use analog connections
		instead, if available.
		• The device is not an audio/video device.
		• Too many other devices are already communicating over
		IEEE 1394. Remove or stop some devices and try again.
38.	The IEEE 1394 device cannot be selected.	• The device may be busy, either recording or a peer-to-peer
		connection has been established. Cancel the recording or
		peer-to-peer connection.
39.	The IEEE 1394 Device is not listed in the Device	• The device is unchecked in the Review screen. Select the Setup
	Selection menu.	menu, then select Review setting. Verify the device is checked.
		• The IEEE 1394 plug is disconnected or loose.
		• The IEEE 1394 Device has not been powered On. Turn on.
		• The device has not been discovered.
		• The device is not an Audio/Video device
40.	DEVICE MENU button does not display a menu.	• The IEEE 1394 device does not provide a menu.
		• The TV cannot support IEEE 1394 menus. See page 46.
41.	All IEEE 1394 devices disappear.	• The connected devices must not be in a loop that returns to the
		TV. Make sure a device is connected at the end.
		• Disconnect all the cables and devices from the TV. Replace them one
		by one to locate the problem device or cable.
		• Use System Reset (front control panel).
42.	Cannot rediscover a deleted IEEE 1394 device	• The device has been disconnected. Plug it in.
		• The device is unchecked in the Review screen. Go to Setup in the
		Main menu, then select Review. Check the device.
		• Remove IEEE 1394 plug. Go to the Edit NetCommand menu. Delete
		the IEEE 1394 device. Plug the device in again so it can be
		discovered again.

91