digital control panel components
PRIMARY SCREEN
Screen 1
Indicates the various modes of the switch settings. Monitors engine RPM - Idle speed 900, High speed 2350. Battery charge indicator - Normal charge 13+ volts. Indicates electrical malfunction - Refer to Troubleshooting section.
INDICATES |
| INDICATES |
STATUS OF PUMP |
| ENGINE RPM |
( ON OR OFF) | LS 600 OFF | 1 |
INDICATES | 0000 ENG RPM |
|
BATTERY 12.5 V | INDICATES | |
BATTERY | LOW OIL PSI | ELECTRIC |
CHARGE |
| MALFUNCTION |
SECONDARY SCREENS
Screen 2
Displays the position of the VOLUME CONTROL switch by indicating whether the increase or decrease position is on or off.
INDICATES VOLUME | FLOW DEC OFF 2 |
| ||
SWITCH IS NOT IN | INDICATES VOLUME | |||
FLOW INC ON |
| |||
THE - POSITION |
| SWITCH IS IN THE | ||
|
|
| + POSITION | |
Screen 3
Displays the number of hours the engine and pump have been used and the number of faults the pump has registered. All three indicators can be reset to zero by the RESET switch on the control panel.
INDICATES NO. |
| INDICATES NO. |
OF HOURS |
| OF HOURS |
ENGINE HAS | E HRS: 00000.0 3 | PUMP HAS |
BEEN USED | BEEN USED | |
| PMP HRS: 00000.0 |
|
| FAULTS: 00000000 |
|
| RESET TO CLEAR | INDICATES NO. |
|
| |
MESSAGE OR |
| OF FAULTS |
INSTRUCTION |
| DETECTED |
Screen 4
Displays the number of strokes the main hydraulic cylinders have gone through. This indicator can be reset to zero by the RESET switch on the control panel.
INDICATES A
RUNNING
COUNT OF
4 NO. OF STROKES STROKE CTR: 0000
PRESS RESET TO
ZERO STROKE CTR
MESSAGE OR
INFORMATION
Screen 5
Displays the ON/OFF electrical signal status of the various 12 volt solenoids (Swing A circuit, Main A circuit, Main B circuit).
INDICATES |
|
| |
SWING A | SWING A OFF | 5 | |
CIRCUIT IS OFF | |||
|
| INDICATES | |
INDICATES | MAIN A OFF | MAIN A | |
CIRCUIT IS OFF | |||
MAIN B OFF | |||
MAIN B |
| ||
|
| ||
CIRCUIT IS OFF |
|
|
Screen 6
Displays the ON/OFF electrical signal status for the Proximity Switch A, Proximity Switch B, Engine Fuel Solenoid, and Unloader Solenoid.
INDICATES |
|
| INDICATES | |
PROXIMITY A | PROX A OFF | 6 | PROXIMITY B | |
CIRCUIT IS OFF | CIRCUIT IS ON | |||
PROX B ON |
| |||
|
|
| ||
INDICATES | FUEL SOL OFF |
| INDICATES | |
UNLOADER OFF |
| |||
UNLOADER |
| FUEL SOLENOID | ||
|
| |||
CIRCUIT IS OFF |
|
| CIRCUIT IS OFF |
Screen 7
Displays the number of times the main hydraulic cylinders stroke and the yards per hour output. This indicator can be reset to zero by the RESET switch on the control panel
INDICATES |
|
| INDICATES THE | |
THROTTLE | THROTTLE ON | 7 | NUMBER OF | |
IS ON | STROKES | |||
STROKES: 20 |
| |||
|
|
| ||
INDICATES THE | STROKES/MIN 8.2 | INDICATES THE | ||
YDS/HR 10.7 |
| |||
NO. OF YARDS |
| NO. OF STROKES | ||
|
| |||
PER HOUR |
|
| PER MINUTE | |
Screen 8
Displays the electrical status of the engine fuel solenoid.To test the
| 8 |
| |
| TO TEST FUEL | INSTRUCTION | |
| SOL PRESS RESET | ||
INDICATES THE | OR MESSAGE | ||
FUEL SOL OFF | |||
FUEL SOLENOID |
| ||
|
| ||
IS OFF |
|
|
Screen 9
Displays the communication status of the (optional) radio remote control.To activate a new remote control connection, use the reset switch on the control panel.
| RADIO ADDRESS 9 | INDICATES | |
| COMMUNICATING |
| THAT RADIO |
|
| ||
INSTRUCTION | PRESS RESET TO | REMOTE IS ON | |
OR MESSAGE | LEARN A NEW ONE |
| |
|
|
| |
MAYCO LS600P CONCRETE PUMP • operation manual — rev. #0 (05/13/13) — page 27
