Serial Transfer Operation, Sck | NEC PD75P308 manual

μPD75P308

SERIAL TRANSFER OPERATION

TWO-LINE AND THREE-LINE SERIAL I/O MODES (SCK: internal clock output)

Parameter

Symbol

Conditions

MIN.

TYP.

MAX.

Unit

Cycle Time

Output

1600

ns

SCK

tKCY1

High-, Low-Level Widths

Output

tKCY1/2-50

ns

SCK

tKH1, tKL1

SI Set-Up Time (vs.

− )

150

ns

SCK

tSIK1

SI Hold Time (vs.

− )

400

ns

SCK

tKSI1

↓ → SO Output

RL = 1kΩ, CL = 100pF*

250

ns

SCK

tKSO1

Delay Time

★*: RL and CL are load resistance and load capacitance of the SO output line.

TWO-LINE AND THREE-LINE SERIAL I/O MODES (SCK: external clock input)

Parameter

Symbol

Conditions

MIN.

TYP.

MAX.

Unit

SCK Cycle Time

tKCY2

Input

800

ns

Input

400

ns

SCK

High-, Low-Level Widths

tKH2, tKL2

−

SI Set-Up Time (vs. SCK

)

tSIK2

100

ns

SI Hold Time (vs.

−

)

400

ns

SCK

tKSI2

↓ → SO Output

RL = 1kΩ, CL = 100pF*

300

ns

SCK

tKSO2

Delay Time

★*: RL and CL are load resistance and load capacitance of the SO output line.

20

Image 20

NEC PD75P308 user manual Serial Transfer Operation, Sck

Contents

Features DescriptionOrdering Information Quality Grade PIN Configuration ΜPD75P308 Block Diagram Contents Port Pins PIN Functions NON Port Pins Input buffer of Cmos standard Schmitt trigger input with hysteresis characteristicsPIN INPUT/OUTPUT Circuits IN/OUT SEG COMType F-B Connect capacitor between VDD and P00/INT4, Reset pin Type M-C Differences Between μPD75P308 and μPD75308 Eprom Program memory address 0 clear mode +12.5 Write mode Verify mode Program inhibit mode Or HWriting and Verifying Prom Program Memory Operation Modes for WRITING/VERIFYING Program Memory Program Memory Write Procedure VDD+1 Program Memory Read Procedure Erasure μPD75P308K only Electrical Specifications Absolute Maximum Ratings Ta = 25C Main System Clock Oscillator Circuit Characteristics Ta = -10 to +70C, VDD = 5 to ±5Recommended Oscillation Circuit Constants Main System Clock Ceramic Oscillator Ta = -10 to +70C Capacitance Ta = 25C, VDD = 0 DC Characteristics Ta = -10 to +70C, VDD = 5V ±5% Operation Other Than Serial Transfer AC Characteristics Ta = -10 to + 70C, VDD = 5V ±5%Interrupt mode register IM0 Serial Transfer Operation SBI Mode SCK internal clock output master SBI Mode SCK external clock output master TI0 Timing AC Timing Test Point excluding X1 and XT1 inputsClock Timing Serial Transfer Timing THREE-LINE Serial I/O Mode TWO-LINE Serial I/O Mode Serial Transfer Timing BUS Release Signal Transfer Command Signal TransferReset Input Timing Interrupt Input Timing BTM3 BTM2 BTM1 BTM0 Data Retention Timing releasing Stop mode by ResetTa = -10 to +70C Other than X1 or MD0 MD1 Program Memory Write TimingProgram Memory Read Timing Package Drawings PIN Plastic QFP 14×20 PIN Ceramic Wqfn Millimeters Inches VPS Recommended Soldering ConditionsΜPD75P308GF-3B9 80-pin plastic QFP 14 x 20 mm Appendix A. Development Tools Prom writing tools Appendix B. Related Documents Processing of Unused Pins Cmos Devices only Static Electricity ALL MOS DevicesStatus Before Initialization ALL MOS Devices Fix the input level of Cmos devices Memo