Appendix A. Development Tools, Prom writing tools | NEC PD75P308

μPD75P308

APPENDIX A. DEVELOPMENT TOOLS

The following development support tools are readily available to support development of systems using μPD75P308:

PROM writing tools

Hardare	IE-75000-R*1		In-circuit emulator for 75K series
	IE-75001-R
	IE-75000-R-EM*2		Emulation board for IE-75000-R and IE-75001-R
	EP-75308GF-R		Emulation prove for μPD75P308GF, provided with 80-pin conversion socket,

		EV-9200G-80	EV-9200G-80.
	PG-1500		PROM programmer
	PA-75P308GF		PROM programmer adapter solely used for μPD75P308GF. It is connected to
			PG-1500.
	PA-75P308K		PROM programmer adapter solely used for μPD75P308K. It is connected to
			PG-1500.

Software	IE Control Program		Host machine

	PG-1500 Controller		• PC-9800 series (MS-DOSTMVer.3.30 to Ver.5.00A*3)
	RA75X Relocatable		• IBM PC/ATTM (PC DOSTM Ver.3.1)
	Assembler

*1: Maintenance product

2:Not provided with IE-75001-R

3:Ver.5.00/5.00A has a task swap function, but this function cannot be used with this software.

Remarks: For development tools from other companies, refer to 75X Series Selection Guide (IF-151).

31

Image 31

NEC PD75P308 user manual Appendix A. Development Tools, Prom writing tools

Contents

Quality Grade FeaturesDescription Ordering Information ΜPD75P308 PIN Configuration Block Diagram Contents PIN Functions Port Pins NON Port Pins PIN INPUT/OUTPUT Circuits Schmitt trigger input with hysteresis characteristicsInput buffer of Cmos standard Type F-B COMIN/OUT SEG Type M-C Connect capacitor between VDD and P00/INT4, Reset pin Eprom Differences Between μPD75P308 and μPD75308 Operation Modes for WRITING/VERIFYING Program Memory Program memory address 0 clear mode+12.5 Write mode Verify mode Program inhibit mode Or H Writing and Verifying Prom Program Memory VDD+1 Program Memory Write Procedure Program Memory Read Procedure Erasure μPD75P308K only Absolute Maximum Ratings Ta = 25C Electrical Specifications Main System Clock Ceramic Oscillator Ta = -10 to +70C Main System Clock Oscillator Circuit CharacteristicsTa = -10 to +70C, VDD = 5 to ±5 Recommended Oscillation Circuit Constants Capacitance Ta = 25C, VDD = 0 DC Characteristics Ta = -10 to +70C, VDD = 5V ±5% Interrupt mode register IM0 AC Characteristics Ta = -10 to + 70C, VDD = 5V ±5%Operation Other Than Serial Transfer Serial Transfer Operation SBI Mode SCK external clock output master SBI Mode SCK internal clock output master Clock Timing AC Timing Test Point excluding X1 and XT1 inputsTI0 Timing TWO-LINE Serial I/O Mode Serial Transfer Timing THREE-LINE Serial I/O Mode Interrupt Input Timing Serial Transfer Timing BUS Release Signal TransferCommand Signal Transfer Reset Input Timing Ta = -10 to +70C Data Retention Timing releasing Stop mode by ResetBTM3 BTM2 BTM1 BTM0 Other than X1 or Program Memory Read Timing Program Memory Write TimingMD0 MD1 PIN Plastic QFP 14×20 Package Drawings Millimeters Inches PIN Ceramic Wqfn ΜPD75P308GF-3B9 80-pin plastic QFP 14 x 20 mm Recommended Soldering ConditionsVPS Prom writing tools Appendix A. Development Tools Appendix B. Related Documents Fix the input level of Cmos devices Processing of Unused Pins Cmos Devices onlyStatic Electricity ALL MOS Devices Status Before Initialization ALL MOS Devices Memo