Hardware Description, Front Panel | NETGEAR WG302v2 instruction

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

Hardware Description

This section describes the WG302v2 front and rear hardware functions.

Front Panel

Figure 0-1

Viewed from left to right, the WG302v2 has these status LEDs: PWR, TEST, LAN, and 802.11g WLAN.

LED	Description

PWR	Power Indicator

	Off	No power. If this LED does not come on with the power adapter and
		cord correctly installed, see Chapter 5, “Troubleshooting.

	On	Power is on.

TEST	Self Test Indicator

	Blink	Indicates self test, loading software, or system fault (if continues).
		Note: This LED may blink for a minute before going off.
LAN	Ethernet link indicator

	Off	No connection detected on the Ethernet link

	Amber On	10 Mbps Ethernet link detected

	Amber Blink	Data is being transmitted or received on the 10 Mbps Ethernet link

	Green On	100 Mbps Fast Ethernet link detected.

	Green Blink	Data is being transmitted or received on the 100 Mbps Ethernet link

Introduction

1-5

v1.0, May 2006

Image 21

NETGEAR WG302v2 manual Hardware Description, Front Panel

Contents

NETGEAR, Inc Technical Support ProSafe 802.11g Wireless Access Point WG302v2 FCC Requirements for Operation in the United States Declaration of ConformityRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese European Spectrum Usage Rules Effective April 11 Except Where NotedChannels 1 to 2.4835 GHz Bestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii Conventions, Formats and Scope About This Manual How to Print this Manual How to Use This Manual V1.0, May Xvi About This Manual Key Features Chapter IntroductionSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products Support Registration card What’s In the Box? Hardware Description Front PanelDescription Rear Panel System Requirements Chapter Basic Installation and Configuration Wireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Rest of World US Only Basic IP Settings V1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Profile Definition Network Authentication Data Encryption Settings Network Authentication TypesAuthentication Description Settings Description AES Wireless Client Security Separation V1.0, May WPA Radius Settings Ssid and Wireless Security Settings Form Configuring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Chapter Management and Information Changing the Administrator Password Remote Management Accessing the CLI by Using the Console Port Using the Secure Telnet Interface CLI Commands Upgrading the Wireless Access Point Firmware Configuration File Management Backing up and Restoring the Configuration Erasing the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information Current IP Settings Field Description Access Point InformationCurrent Wireless Settings General Information Fields Viewing the Activity Log Viewing the Available Wireless Station List Access Point Statistics Viewing StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Configuring Advanced IP Settings for Wireless Clients Chapter Advanced Configuration V1.0, May Configuring Advanced Wireless Settings Configuring Hotspot Settings Configuring Wireless LAN Parameters Modifying QoS Queue Parameters Advanced Wireless LAN Parameters QoS Queue Description QoS Queues and Parameters Wireless Bridging and Repeating V1.0, May LAN Segment Point-to-Point Bridge Configuration Multi-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May No lights are lit on the access point Chapter Troubleshooting LAN light is not lit Wireless LAN activity light does not light up When I enter a URL or IP address I get a timeout error Cannot connect to the WG302v2 to configure it Am unable to download files from some FTP sites Need to restore factory default settings Document Link Appendix a Related Documents V1.0, May Appendix B Specifications Default Factory SettingsTable B-1 Access Point Default Configuration Settings Wireless Settings Feature DescriptionSecurity Profile Settings Radius Server Settings Dhcp Server Settings Feature Description Remote ManagementWireless LAN Parameters Other Settings Specifications for the WG302v2 Table B-2 WG302v2 Technical SpecificationsParameter ProSafe 802.11g Wireless Access Point Accessing CLI TAB Completion Help Appendix C Command Line Reference Keyboard Shortcuts Table C-1 Keyboard ShortcutsKeyboard Shortcut Action on CLI Interface Naming Conventions Table C-2 Interface Naming ConventionInterface Description Entering CLI Commands Table C-3 Commands at the Blank PromptCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status down Set vap vap0 with radio Wlan0 status upSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-text Set interface wlan0 wep-key-1 abcde Set interface wlan0 wep-key-1 keySet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmno Radius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Advanced Wireless Settings Hotspot Settings Set radio wlan0 wme on Set bss wlan0bssvap0 dtim-periodSet radio wlan0 wme off Get tx-queue Advanced Access Point Settings V1.0, May