Industry Canada Compliance Statement | NETGEAR WG302v2 guide

Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the wireless access point.

RF Exposure Warning for North America, and Australia

WARNING! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device (see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be colocated with other antenna or radio transmitter.

Antenna Statement for North America and Australia

In addition to its own antenna, the WG302v2 device has been approved for use with the following detachable antennas and antenna cables.

Approved	Antenna Gain and	Approved Antenna	Antenna Cable	Maximum Transmitted
Antennas	type	Cable	Length	Powera

NETGEAR	14.5 dBi, directional	NETGEAR ACC-10314-	1.5 m to 30 m	18 dBm + 14.5 dBi ant.
ANT24D18v2	outdoor/indoor	01 thru 05

NETGEAR	9 dBi,	NETGEAR ACC-10314-	1.5 m to 30 m	18 dBm + 9 dBi ant.
ANT2409	omnidirectional	01 thru 05
	outdoor/indoor
NETGEAR	5 dBi, ceiling/wall	NETGEAR ACC-10314-	1.5 m to 30 m	18 dBm + 5 dBi ant.
ANT24O5	indoor	01 thru 05

a. WG302v2 maximum radiated power in North America and Australia: 19 dBm – cable loss + antenna gain

Please see the product specifications at http://kbserver.netgear.com/products/wg302.asp for an updated list of wireless accessories approved to be used with the WG302v2.

Industry Canada Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations ICES 003.

Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur NMB-003.

The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

iv

v1.0, May 2006

Image 4

NETGEAR WG302v2 manual Industry Canada Compliance Statement

Contents

NETGEAR, Inc ProSafe 802.11g Wireless Access Point WG302v2 Technical Support Declaration of Conformity FCC Requirements for Operation in the United StatesRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese Except Where Noted European Spectrum Usage Rules Effective April 11Channels 1 to 2.4835 GHz Bestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii About This Manual Conventions, Formats and Scope How to Use This Manual How to Print this Manual V1.0, May Xvi About This Manual Chapter Introduction Key FeaturesSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products What’s In the Box? Support Registration card Front Panel Hardware DescriptionDescription Rear Panel Chapter Basic Installation and Configuration System Requirements Wireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Basic IP Settings Rest of World US Only V1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Network Authentication Profile Definition Network Authentication Types Data Encryption SettingsAuthentication Description Settings Description Wireless Client Security Separation AES V1.0, May Ssid and Wireless Security Settings Form WPA Radius Settings Configuring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Changing the Administrator Password Chapter Management and Information Remote Management Using the Secure Telnet Interface Accessing the CLI by Using the Console Port Upgrading the Wireless Access Point Firmware CLI Commands Configuration File Management Erasing the Configuration Backing up and Restoring the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information Field Description Access Point Information Current IP SettingsCurrent Wireless Settings General Information Fields Viewing the Activity Log Viewing the Available Wireless Station List Viewing Statistics Access Point StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Chapter Advanced Configuration Configuring Advanced IP Settings for Wireless Clients V1.0, May Configuring Hotspot Settings Configuring Advanced Wireless Settings Configuring Wireless LAN Parameters Advanced Wireless LAN Parameters Modifying QoS Queue Parameters QoS Queues and Parameters QoS Queue Description Wireless Bridging and Repeating V1.0, May Point-to-Point Bridge Configuration LAN Segment Multi-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May Chapter Troubleshooting No lights are lit on the access point Wireless LAN activity light does not light up LAN light is not lit Cannot connect to the WG302v2 to configure it When I enter a URL or IP address I get a timeout error Need to restore factory default settings Am unable to download files from some FTP sites Appendix a Related Documents Document Link V1.0, May Default Factory Settings Appendix B SpecificationsTable B-1 Access Point Default Configuration Settings Feature Description Wireless SettingsSecurity Profile Settings Radius Server Settings Feature Description Remote Management Dhcp Server SettingsWireless LAN Parameters Other Settings Table B-2 WG302v2 Technical Specifications Specifications for the WG302v2Parameter ProSafe 802.11g Wireless Access Point Appendix C Command Line Reference Accessing CLI TAB Completion Help Table C-1 Keyboard Shortcuts Keyboard ShortcutsKeyboard Shortcut Action on CLI Table C-2 Interface Naming Convention Interface Naming ConventionsInterface Description Table C-3 Commands at the Blank Prompt Entering CLI CommandsCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status up Set vap vap0 with radio Wlan0 status downSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-text Set interface wlan0 wep-key-1 key Set interface wlan0 wep-key-1 abcdeSet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmno Radius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Hotspot Settings Advanced Wireless Settings Set bss wlan0bssvap0 dtim-period Set radio wlan0 wme onSet radio wlan0 wme off Get tx-queue Advanced Access Point Settings V1.0, May