V1.0, May | NETGEAR WG302v2 specs

NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual

c.Connect an Ethernet cable from your WG302v2 to a LAN port on your router, switch, or hub.

Note: By default, the DHCP client on the WG302v2 is disabled. If your network uses dynamic IP addresses, you must change this setting. To connect to the

WG302v2 after the DHCP server on your network assigns it a new IP address, enter the access point name into your Web browser. The default access point name is netgearxxxxxx, where xxxxxx represents the last 6 bytes of the MAC address. The default name is printed on the bottom label of the WG302v2.

d.Connect the power adapter to the wireless access point and plug the power adapter in to a power outlet. The PWR, LAN, and WLAN lights should light up.

4.Verify wireless connectivity.

Using a computer with an 802.11b/g wireless adapter with the correct wireless settings needed to connect to the WG302v2 (SSID, WEP/WPA, MAC ACL, etc.), verify connectivity by using

abrowser such as Mozilla Firefox, Netscape, or Internet Explorer to browse the Internet, or check for file and printer access on your network.

Note: The default SSID is NETGEAR.The SSID of any wireless access adapters must match the SSID you configure in the ProSafe 802.11g Wireless Access

Point. If they do not match, you will not get a wireless connection to the WG302v2.

Note: If you are unable to connect to the WG302v2 with a wireless client, see Chapter 5, “Troubleshooting

2-6	Basic Installation and Configuration

v1.0, May 2006

Image 28

NETGEAR WG302v2 manual V1.0, May

Contents

NETGEAR, Inc ProSafe 802.11g Wireless Access Point WG302v2 Technical Support Declaration of Conformity FCC Requirements for Operation in the United StatesRadio Frequency Interference Warnings & Instructions Industry Canada Compliance Statement Europe EU Declaration of Conformity Malti Maltese Except Where Noted European Spectrum Usage Rules Effective April 11Channels 1 to 2.4835 GHz Bestätigung des Herstellers/Importeurs Contents Chapter Management and Information Appendix a Related Documents Appendix B Specifications Xii About This Manual Conventions, Formats and Scope How to Use This Manual How to Print this Manual V1.0, May Xvi About This Manual Chapter Introduction Key FeaturesSupported Standards and Conventions WG302v2 Key Features Compatible and Related Netgear Products What’s In the Box? Support Registration card Front Panel Hardware DescriptionDescription Rear Panel Chapter Basic Installation and Configuration System Requirements Wireless Equipment Placement and Range Guidelines Installing the ProSafe 802.11g Wireless Access Point Click to view documentation V1.0, May V1.0, May Logging in to the WG302v2 Using Its Default IP Address Basic IP Settings Rest of World US Only V1.0, May Wireless Settings V1.0, May Understanding WG302v2 Wireless Security Options Configuring Security Profiles Selected Security Profile Network Authentication Profile Definition Network Authentication Types Data Encryption SettingsAuthentication Description Settings Description Wireless Client Security Separation AES V1.0, May Ssid and Wireless Security Settings Form WPA Radius Settings Configuring the Radius Server Settings Restricting Wireless Access by MAC Address V1.0, May Changing the Administrator Password Chapter Management and Information Remote Management Using the Secure Telnet Interface Accessing the CLI by Using the Console Port Upgrading the Wireless Access Point Firmware CLI Commands Configuration File Management Erasing the Configuration Backing up and Restoring the ConfigurationUsing the Reset Button to Restore Factory Default Settings Viewing General Information Field Description Access Point Information Current IP SettingsCurrent Wireless Settings General Information Fields Viewing the Activity Log Viewing the Available Wireless Station List Viewing Statistics Access Point StatisticsField Description Rogue AP Detection V1.0, May V1.0, May Chapter Advanced Configuration Configuring Advanced IP Settings for Wireless Clients V1.0, May Configuring Hotspot Settings Configuring Advanced Wireless Settings Configuring Wireless LAN Parameters Advanced Wireless LAN Parameters Modifying QoS Queue Parameters QoS Queues and Parameters QoS Queue Description Wireless Bridging and Repeating V1.0, May Point-to-Point Bridge Configuration LAN Segment Multi-Point Bridge Configuration Repeater with Wireless Client Association Parent AP in Repeater Mode V1.0, May V1.0, May Chapter Troubleshooting No lights are lit on the access point Wireless LAN activity light does not light up LAN light is not lit Cannot connect to the WG302v2 to configure it When I enter a URL or IP address I get a timeout error Need to restore factory default settings Am unable to download files from some FTP sites Appendix a Related Documents Document Link V1.0, May Default Factory Settings Appendix B SpecificationsTable B-1 Access Point Default Configuration Settings Feature Description Wireless SettingsSecurity Profile Settings Radius Server Settings Feature Description Remote Management Dhcp Server SettingsWireless LAN Parameters Other Settings Table B-2 WG302v2 Technical Specifications Specifications for the WG302v2Parameter ProSafe 802.11g Wireless Access Point Appendix C Command Line Reference Accessing CLI TAB Completion Help Table C-1 Keyboard Shortcuts Keyboard ShortcutsKeyboard Shortcut Action on CLI Table C-2 Interface Naming Convention Interface Naming ConventionsInterface Description Table C-3 Commands at the Blank Prompt Entering CLI CommandsCommand Description Using the CLI to Configure the ProSafe 802.11g Viewing General Information Configuring Basic Settings Configuring Wireless Settings Configuring Security Profile Settings Set vap vap0 with radio Wlan0 status up Set vap vap0 with radio Wlan0 status downSet interface wlan0vap0 Ssid ssidname Set interface wlan0 security plain-text Set interface wlan0 wep-key-1 key Set interface wlan0 wep-key-1 abcdeSet interface wlan0 wep-key-2 fghi Set interface wlan0 wep-key-3 klmno Radius Server Settings Access Control Viewing and Configuring Management Settings Viewing and Configuring System Information Configuring Advanced IP Settings Hotspot Settings Advanced Wireless Settings Set bss wlan0bssvap0 dtim-period Set radio wlan0 wme onSet radio wlan0 wme off Get tx-queue Advanced Access Point Settings V1.0, May