Verifying Shipment Contents | Nortel Networks 114200-E instruction

Installing and Operating Passport ARN Routers

•Your installation site meets physical, electrical, and environmental requirements.

•You have the communications devices and the cabling that you need to attach to the ARN.

Verifying Shipment Contents

You should inspect all items for shipping damage. If you detect any damage, do not install the ARN. Call the Nortel Networks Technical Solutions Center in your area, as described in “How to Get Help.”

In addition to the ARN and this guide, your shipping container should contain several other hardware accessory items. Verify that the items in the shipping container match those on the packing list affixed to the shipping container.

Refer to the following checklist when verifying the contents of the shipping container:

__ One power cable for connecting the ARN to a wall outlet.

__ One console/modem cable kit (Order No. 110310) for connecting an optional local console or modem. The console/modem cable kit contains one 15-foot AT standard molded serial cable (with DB-9 receptacle to DB-25 plug connectors) and one null modem crossover adapter (with DB-25 to DB-25 receptacle connectors).

__ Two flange brackets, eight #6 Phillips screws, four #10 cagenut screws and washers, and four cage nuts for rack-mounting the ARN.

___Four rubber feet for table-top operation.

Figure 1-1 illustrates the ARN hardware accessory items.

1-2	114200-E Rev 00

Image 26

Nortel Networks 114200-E manual Verifying Shipment Contents

Contents

Installing and Operating Passport ARN Routers Statement of Conditions Copyright 2000 Nortel NetworksTrademarks USA Requirements Only Canada Requirements Only Japan/Nippon Requirements OnlyTaiwan Requirements Canada CS-03 -- Règles et règlements FCC Part 68 Compliance Statement Nortel Networks NA Inc. Software License Agreement Vii Page Contents Chapter Starting the ARN Chapter Installing a WAN Adapter Module Appendix B Using Local Boot the Quick-Start Procedure Appendix D Requirements for European Operation Page Figures Figure B-1 Tables Table C-2 Preface Before You Begin Ping Text ConventionsBold text Example Enter show ip alerts routes Acronyms Channel service unit Challenge handshake authentication protocolCarrier sense multiple access with collision detection Data service unit Hard-Copy Technical Manuals How to Get Help Technical Solutions Center Telephone Preparing to Install the ARN Topic Verifying Shipment Contents Accessories in the ARN Shipping Container Management Console Additional EquipmentCables Mounting Hardware Verifying Site Requirements Installing the ARNInstallation Space Requirements Positioning the ARN on a Flat Surface Rack-Mounting the ARN Determine how you want the ARN to fit in the equipment rack Options for Attaching Flange Brackets to Rack-Mount the ARN Installing the ARN in an Electronic Enclosure Rack Understanding the ARN Module Locations ARN Module Locations Connecting Communications Cables Connecting to an Ethernet Interface Connecting to the AUI Cable must have a 15-position D-SUB receptacle Connecting to the UTP Interface Connecting an Ethernet 10BASE-T Cable Connecting to a Token Ring Interface Connecting to the Fiber Interface Connecting to the STP Interface Connecting a Token Ring STP Cable Connecting to a Serial Interface 10. Connecting a Token Ring UTP Cable COM3 Connecting to the Isdn Interface 13. Connecting the Isdn BRI Cable Connecting to the 56/64K DSU/CSU Interface Connecting to the FT1/T1 DSU/CSU Interface Connecting to the E1/FE1 DSU/CSU Interface 15. Connecting the FT1/T1 DSU/CSU Cable Connecting to the Integrated V.34 Modem 17. Connecting a Telephone Cable Modem Signal/Parameter Default Value Connecting to the X.25 PAD InterfaceFront-Panel Modem Adapter Module Defaults To connect X.25 PAD services 18. Connecting a Breakout Box to the X.25 PAD Interface Baud rate Data bits Stop bit No parity Connecting a Management ConsoleConnecting a PC Console 19. Connecting the Console/Modem Cable Connecting a Terminal Console 21. Connecting a PC Console to an ARN Console Parameters Parameter Value Connecting a Console Modem Console Modem Defaults Connecting an External Console Modem Connecting to an Integrated V.34 Console Modem Module Connecting the Power Cable 24. Connecting to an Integrated Console Modem 25. Connecting the Power Cable to the ARN Installing the Flash Memory Card 26. Flash Memory Card Where to Go Next For information about Go to Understanding the Startup Process Topic Go to Summary of Initial Startup Options Router does not operate Supported Boot Options by Interface Interface Supported Not Supported Starting the ARN for the First Time Using EZ-Install Using Netboot, Directed Netboot, or Local Boot Interrupting the Boot Process Manager Logging in to the Command Line SoftwareARN monitor login prompt appears Continuing with Netboot Getcfg Starting the ARN Continuing with Directed Netboot To use the directed netboot feature Verifying Directed Netboot Configuration Continuing with Local Boot the Quick-Start Procedure Bconfig config local Run instarn.bat Technician Interface prompt $ appearsQuick-Start script begins running Where to Go Next Page Chapter Operating the ARN Understanding the ARN LEDs Base Module Diagnostic LEDs Diagnostic LEDsDescribes the base module diagnostic LEDs Base Module LEDs Base Module Ethernet 10BASE-T LEDs Ethernet 10BASE-T LEDsDescribes the base module Ethernet 10BASE-T LEDs Token Ring LEDs Ethernet 10/100BASE-Tx LEDsEthernet 100BASE-Fx LEDs Describes the expansion module token ring LEDs Expansion Module LEDsEthernet LEDs Expansion Module Ethernet LEDs Describes the expansion module serial interface LEDs Adapter Module LEDsSerial LEDs Serial LED 56/64K DSU/CSU LEDs Isdn BRI LEDs S/T or U Interfaces10 describes the Isdn adapter module LEDs 11 describes the 56/64K DSU/CSU adapter module LEDs 13 describes the X.25 PAD adapter module LEDs FT1/T1 and FE1/E1 DSU/CSU LEDsPAD LEDs Modem LEDs Ensuring a Successful Installation Modem LEDs Boot Status LEDs Boot Status Run LED Boot LED Powering On and Off ARN power switch is located on the back panel Figure Resetting the ARN ARN Reset Button Removing a Flash Memory Card To remove a memory card from an ARN Memory Card Read/Write Protect Switch Protecting Memory Card Files Where to Go Next Page Installing a WAN Adapter Module Preparing for Installation Before installing a WAN adapter module Downloading New Boot and Diagnostic CodePowering Down Set the power switch to 0, off refer to -25 on Removing the Filler Panel Location of Adapter Module Slots 1 Removing the Filler Panel from Slot Removing an Adapter Module To remove a WAN adapter module Installing an Adapter Module To install a WAN adapter module Securing the Adapter Module to the Front Panel What to Do Next Topic Using the ifconfig Command 56 64 -fr -annexd -lmi -annexa-intclk Table A-1 COM Interface ifconfig Command Settings Configuring an Ethernet Interface for Network Booting Table A-2. Ethernet Interface ifconfig Command Settings Configuring a Token Ring Interface for Network Booting Table A-3 Token Ring Interface ifconfig Command Settings Enabling and Disabling Interfaces with ifconfig Examples of ifconfig Commands Bconfig -d image config Using the bconfig CommandFormat for the bconfig Command Bconfig image config local network TFTPhost TFTPpathname Bconfig image network bconfig config network Verifying Your ConfigurationExamples of bconfig Commands Boot Options Page Appendix B Using Local Boot the Quick-Start Procedure Understanding Quick-Start Connector Names and Numbers Before You Run Quick-Start Module Interface Base Expansion Adapter Table B-1 Quick-Start Connector Names and NumbersFilling Out the Worksheets Fill out one Wide Area Protocol worksheet Step Requested Information Options Your Response Global Information WorksheetGlobal Information Worksheet COM1 COM2 COM3 COM4 COM5 Global Information Worksheet Requested Information Options Your Response Router Protocol WorksheetsRIP Worksheet RIP Worksheet Ospf Worksheet Nbma Static Route to Site Manager Worksheet Nortel Networks Proprietary PPP Worksheet Wide Area Protocol WorksheetsStatic Route to Site Manager Worksheet Nortel Networks Proprietary PPP Worksheet PPP Standard Worksheet Chap PPP Standard Worksheet Smds Worksheet Technician Interface login prompt appearsRunning the Quick-Start Script Press Control-c Table B-2 Quick-Start CommandsTask Action Details To cancel the test, enter q Figure B-2. Starting the IP Interface Test Appendix C ARN Technical Specifications Physical Specifications Table C-1 ARN Wall Outlet Requirements Electrical SpecificationsEnvironmental Specifications Country Outlet Voltage Hardware Communications Options One 56/64K DSU/CSU interface One Isdn BRI U interfaceOne V.34 modem interface One FE1/E1 DSU/CSU interface Table C-2 Network Interfaces Available on ARNs Table C-3 AUI Pin Assignments Pin Assignment Pin No Signal NameEthernet Attachment Unit Interface AUI Pin Assignment Pin No Signal Function Ethernet 10BASE-T and 10/100BASE-Tx Interfaces Token Ring STP Interface Table C-5. Token Ring STP Interface Pin Assignments Table C-6. Token Ring UTP Interface Pin Assignments Token Ring UTP InterfaceSerial Interfaces Pin Assignment Pin No. Signal Name Table C-7 Serial Interface Pin Assignments Table C-8. Isdn BRI U Interface Pin Assignments Pin Assignment Pin No SignalIsdn BRI U Interface Isdn BRI S/T Interface Table C-9. Isdn BRI S/T Interface Pin Assignments Table C-10 /64K DSU/CSU Interface Pin Assignments 56/64K DSU/CSU InterfaceFT1/T1 DSU/CSU Connections Table C-11 lists the ARN FT1/T1 DSU/CSU connector pinouts Table C-11 RJ-48C Connector Pinouts Table C-12 Breakout Box Interface Pin Assignments Signal Pin Assignment Pin No FunctionPAD Connections Table C-13. V.34 Interface Pin Assignments RJ-11 Interface for V.34 ModemLocal Console Connections Table C-14. Local Console Port DB-9 Pin Assignments Service Modem ConnectionsPin Assignment Pin No Signal Name Direction Table C-15. Service Modem Port DB-9 Pin Assignments ARN Ethernet Base Model Safety Status Port Location Port Description Type of Circuit ARN 10/100BASE-T Ethernet Base Model Safety Status ARN Token Ring Base Model Safety Status ARN Expansion Modules Safety Status Synchronous Cabling Requirements Nortel Networks Termination Remote Termination Pin Signal Local Wire Connections Pin 7 30 31 Pin 13 Pin 14 Rev Send Data a Table D-7 Interface Order No Table D-8 Interface Order No Figure D-5. Cable 7224 X.21 Compliant Table D-9 Interface Order No Pin 46 48 GRD Pin 38 Pin 14 Table D-11 Safety Status Order No. CV0004001 Serial Adapter Module Requirements Table D-13 Isdn Connector Pinouts Table D-13 lists the Isdn connector pinoutsTable D-12 Isdn BRI Safety Status Order No. CV0004002 Pin Signal Amperage Power Requirements for Isdn BRI and Serial Adapter ModulesTable D-14. Isdn BRI Power Requirements Voltage used or generated by other parts Clearance Creepage Y Host or expansion card Requirements for European Operation Page Numbers 10BASE-T Index-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8