Node Parameter | Nortel Networks 21 PCI 10/100, W/WOL manual

Installation and Reference for the BayStack 21 PCI 10/100 Adapter w/WOL

NODE Parameter

You can use the NODE parameter to replace the default node address associated with your electrically erasable programmable read-only memory (EEPROM).

The following is an example of a typical NODE parameter:

LOAD B21LAN10 NODE=0000E8001122

Medium Parameter

The Medium parameter specifies which medium type is used by the BayStack 21 network driver. The medium type refers to the transmission type.

Accepted values include:

•AUTO (sense)

•100FULL (duplex mode)

•100HALF (duplex mode)

•10FULL (duplex mode)

•10HALF (duplex mode)

The following is an example of a typical Medium parameter:

LOAD B21LAN10 SLOT=3 FRAME=ETHERNET_802.2 Medium=100Full

B-4

206379-A

Image 70

Nortel Networks 21 PCI 10/100, W/WOL manual Node Parameter

Contents

Part No -A September Great America Parkway Santa Clara, CA USA Requirements Only Copyright 1999 Nortel NetworksTrademarks EN 55 022 Statement Voluntary Control Council for Interference Vcci Statement 206379-A Restricted Rights Legend Nortel Networks NA Inc. Software License Agreement Vii Viii Contents Chapter Using the WOL Feature Appendix B Novell NetWare Reference Information Xii Figures 26. Microsoft TCP/IP Properties Dialog Box Tables Xvi Before You Begin PrefaceText Conventions Technical Publications How to Get Help Technical Solutions Center Telephone Number Chapter Introduction BayStack 21 PCI 10/100 Adapter w/WOL Overview Product Description Product FeaturesBayStack 21 Network Card RJ-45 Ethernet Port LEDs WOL Cable and Connector Describes the Link and Activity LED indications WOL Connector System Requirements Operating Environments Supported Operating Systems Fast Ethernet Cables 100 Mb/s Cable RequirementsEthernet Cables 10 Mb/s Page Chapter Hardware Installation Package Contents Installing the BayStack 21 PCI 10/100 Adapter w/WOL Connecting the WOL Cable Page Chapter Software Installation Installing the Network Driver in a Windows 95 Environment PreinstallationTurn on the power to the workstation, and start Windows New Hardware Found Window-BayStack Network Card Update Device Driver Wizard Click Next Click Finish Remove any CDs from your CD drive Click Yes Configuring the Workstation Identification Configuring the Windows 95 EnvironmentSelect the Identification tab Figure System Settings Change Dialog Box Enter the following information for your workstation Configuring the Network Properties Network Dialog Box-Configuration Tab Click Add Select Protocol Click Add 11. Configuration Tab, BayStack 21 Network Card Selected Click Properties 12. TCP/IP Properties Dialog Box Installing the Network Driver in a Windows 98 Environment Remove all CDs from the CD drive Click Yes 14. New Hardware Found Window 16. Copying Files Dialog Box 18. System Settings Change Dialog Box Select one of the following options Configuring the Windows 98 Environment Select Nortel BayStack 21 10/100 PCI Ethernet Adapter 20. TCP/IP Properties Dialog Box Installing the Network Driver in a Windows NT Environment Select the Adapters tab Figure Select Add Click Have Disk Select Auto Click OK 23. Select OEM Option Dialog Box Configuring the Network Properties Click the Protocols tab Microsoft TCP/IP Properties dialog box opens Figure Click Close Installing the Network Driver in a Novell NetWare ServerFrom the Installation Options menu, select Driver options Type Press Enter Specifying Driver Parameters Press Enter at each of the following four prompts Installing the Network Card in a Novell NetWare Client Enter the following commands, in order Chapter Using the WOL Feature Setting Up the Workstation Running the WOL Feature Open a WOL utility, such as the Magic Packet Utility Figure Magic Packet Utility identification window opens Figure Send a Magic Packet to One Host dialog box opens Figure Chapter Troubleshooting Diagnostic LEDs Hardware Issues Software Issues Typical PCI Slot Parameters Page Appendix a Technical Specifications Product Specifications Table A-1. Technical Specifications Software Drivers Appendix B Novell NetWare Reference Information Novell NetWare Server AUTOEXEC.NCF Files and Parameters One Network Card Installed Sample AUTOEXEC.NCF File Parameters Slot Parameter Node Parameter Client Commands Novell NetWare Client Commands and NET.CFG FileSample NET.CFG Files Page Index Numbers Index-2