Sample network setup Meridian | Nortel Networks P0605618 manual

1001rp server description

Standard 1.0

Sample network setup: Meridian 1

The following diagram shows a CallPilot server sample network setup with a Meridian 1 switch. The Meridian 1 switch can be one of the following:

Option 11C or Option 11C Mini

Option 51C

ÑOption 61C Options 81 and 81C

Desktop	Desktop	Web-enabled
client PC	client PC	administrative
		PC
	Customer LAN (optional)
	Modem
Meridian 1 switch	CallPilot server
		Router or
	MPB16-4	Ethernet
MGate	board	switch
MGate		(optional)
card		(optional)
card
	Embedded LAN
Laptop		Web-enabled
		administrative
		PC
		G101626
20		CallPilot

Image 20

Nortel Networks P0605618, 555-7101-217 manual Sample network setup Meridian, Customer LAN optional

Contents

CallPilot P0605618 CallPilot Page Publication history Publication history Contents Index Installing the server and connecting the peripheralDevices 1001rp server description A p t e r Server features Server dimensions and weightIntroduction 49.5 cm 19.5 Front panel features front view without the front bezel Alarm board Rear panel diagram Overhead view of empty server showing PCI and ISA connectors 1001rp slot assignments Slot assignmentsSlot definition and slot numbering Single Board Computer Slot Reserved for COM1 COM2 I/O bracket SlotElan Network card Slot Clan Network card Slot 12b BRD20 IRQ mapping table IRQ Network connectivity Sample network setup Meridian Customer LAN optional Sample network setup Succession CSE Telephony LAN/Customer LAN 10/100BaseT or 100BaseT Switch connectivity CallPilot Elan and Clan network setup Remote access connectivity Network requirements Supported peripheral devices Modem Kbps external modem NTRH9078 providesSince the modem is an external device, it requires its own Also supported, but has been replaced by the 56 Kbps Preparing for installation Installation overview Installation checklist May 2003Preparing for installation Conventions for warnings To unpack the equipment Follow this procedure to unpack the server and peripheralsUnpacking the 1001rp server What’s next? Removing the front bezel and server cover About the front bezel doors To remove the front bezel Continue with Inspecting the server interior on To remove the server coverHigh current inside the chassis can cause severe injury To replace the front bezel after installation is complete Inspecting the server interior To inspect the server interior Preparing for installationStandard Power supply installation Equipment handling guidelines Safety precautionsSafety information Section a Installing the power supply modules AC or DC AC versus DC systems Installing the second power supply module AC or DCAbout the power supply module Power supply modules To install the power supply module Do one of the following Section B Setting up DC power source for a 1001rp DC server DC wire gauge tables Metric wire conversion Following diagram shows typical rack power cabling DC rack cabling 48VDC power distribution rationale About the Power Distribution Unit Multiple PDUs PDU terminal blocks and wiring diagram DC power input Bringing power and ground into the PDU To bring DC power and ground into the PDU May Power supply installation Installing the server and connecting the peripheral devices Installing the server To install the server Preparing the modem Required equipment Modem DIP switches DIP To set the modem DIP switches OFF The modem sends a CD signal when it OFF Loads Y or Y1 configuration fromAT command set recognition OFF Disables command recognition dumb Connecting peripherals to the server Rear panel connections To connect the mouse, keyboard, and monitor to the server To connect the modem to the server Continue with Connecting the server to the Elan on To connect the server to the Elan Connecting the server to the ElanMedia Access Control address Feature key adapter dongle. See Connecting the server to the Clan optional To connect the server to the Clan What’s next? Installing the Nortel Networks software feature key adapter To install the software feature key adapter For installation, you require a Phillips No screwdriverContinue with Connecting the server to power on Requirements Connecting the server to power Before you begin CallPilot server To connect the 1001rp AC server to power To connect the 1001rp DC server to power Connect the DC power cable to the server, as shown below To start the server Binder Installing the server and connecting the peripheral devices Index Clan Elan May Index Index Page Product release Document release Standard Date May